- 您現在的位置：買賣IC網 > PDF目錄377699 > LT1372IS8 (LINEAR TECHNOLOGY CORP) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF資料下載
參數資料
| 型號： | LT1372IS8 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | 2.7 A SWITCHING REGULATOR, 580 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | 0.150 INCH, PLASTIC, SO-8 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 274K |
| 代理商： | LT1372IS8 |
7
LT1372/LT1377
APPLICATIU
Positive fixed voltage versions are available (consult
Linear Technology marketing).
U
W
U
Negative Output Voltage Setting
The LT1372/LT1377 develops a –2.49V reference (V
NFR
)
from the NFB pin to ground. Output voltage is set by
connecting the NFB pin to an output resistor divider
(Figure 2). The –30
μ
A NFB pin bias current (I
NFB
) can
cause output voltage errors and should not be ignored.
This has been accounted for in the formula in Figure 2. The
suggested value for R2 is 2.49k. The FB pin is normally left
open for negative output application. See Dual Polarity
Output Voltage Sensing for limitatins on FB pin loading
when using the NFB pin.
Shutdown and Synchronization
The dual function S/S pin provides easy shutdown and
synchronization. It is logic level compatible and can be
pulled high, tied to V
IN
or left floating for normal operation.
A logic low on the S/S pin activates shutdown, reducing
the part’s supply current to 12
μ
A. Typical synchronization
range is from 1.05 to 1.8 times the part’s natural switching
frequency, but is only guaranteed between 600kHz and
800kHz (LT1372) or 1.2MHz and 1.6MHz (LT1377). A
12
μ
s resetable shutdown delay network guarantees the
part will not go into shutdown while receiving a synchro-
nization signal.
Caution should be used when synchronizing above 700kHz
(LT1372) or 1.4MHz (LT1377) because at higher sync
frequencies the amplitude of the internal slope compensa-
tion used to prevent subharmonic switching is reduced.
This type of subharmonic switching only occurs when the
duty cycle of the switch is above 50%. Higher inductor
values will tend to eliminate problems.
Thermal Considerations
Care should be taken to ensure that the worst-case input
voltage and load current conditions do not cause exces-
sive die temperatures. The packages are rated at 120
°
C/W
for SO (S8) and 130
°
C/W for PDIP (N8).
Average supply current (including driver current) is:
I
IN
= 4mA + DC (I
SW
/60 + I
SW
×
0.004)
I
SW
= switch current
DC = switch duty cycle
Switch power dissipation is given by:
P
SW
= (I
SW
)
2
×
R
SW
×
DC
R
SW
= output switch “On” resistance
Total power dissipation of the die is the sum of supply
current times supply voltage plus switch power:
P
D(TOTAL)
= (I
IN
×
V
IN
) + P
SW
Dual Polarity Output Voltage Sensing
Certain applications benefit from sensing both positive
and negative output voltages. One example is the “Dual
Output Flyback Converter with Overvoltage Protection”
circuit shown in the Typical Applications section. Each
output voltage resistor divider is individually set as de-
scribed above. When both the FB and NFB pins are used,
the LT1372/LT1377 acts to prevent either output from
going beyond its set output voltage. For example in this
application, if the positive output were more heavily loaded
than the negative, the negative output would be greater
and would regulate at the desired set-point voltage. The
positive output would sag slightly below its set-point
voltage. This technique prevents either output from going
unregulated high at no load. Please note that the load on
the FB pin should not exceed 250
μ
A when the NFB pin is
used. This situation occurs when the resistor dividers are
used at bothFB and NFB. True load on FB is not the full
divider current unless the positive output is shorted to
ground. See Dual Output Flyback Converter application.
R1
–V
OUT
= V
NFB
+ I
NFB
(R1)
1 +
R2
LT1372 F02
NFB
PIN
V
NFR
I
NFB
–V
OUT
(
)
R1
R2
R1 =
+ 30
×
10
–6
V
OUT
– 2.49
) (
(
)
2.49
R2
Figure 2. Negative Output Resistor Divider
相關PDF資料 |
PDF描述 |
|---|---|
| LT1372 | 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C |
| LT1373CN8 | Synchronous 4-Bit Up/Down Binary Counters With 3-State Outputs 20-SOIC 0 to 70 |
| LT1373IN8 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LT1373IS8 | CRYSTALS 50/100 0+70 18PF 13.8244MHZ ATCUT FUND HC-49/UP |
| LT1373CS8 | Synchronous 4-Bit Up/Down Binary Counters With 3-State Outputs 20-SOIC 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1372IS8#PBF | 功能描述:IC REG MULTI CONFIG ADJ 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LT1372IS8#PBF | 制造商:Linear Technology 功能描述:IC SWITCHING REGULATOR 8-SOIC 制造商:Linear Technology 功能描述:IC, SWITCHING REGULATOR, 8-SOIC |
| LT1372IS8#TR | 功能描述:IC REG MULTI CONFIG ADJ 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT1372IS8#TRPBF | 功能描述:IC REG MULTI CONFIG ADJ 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT1372IS8PBF | 制造商:Linear Technology 功能描述:DC-DC Converter Step-Up/Down 25V SOIC8 |
發布緊急采購，3分鐘左右您將得到回復。