參數資料
型號: LT1371IT7
廠商: LINEAR TECHNOLOGY CORP
元件分類: 穩壓器
英文描述: RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
中文描述: SWITCHING REGULATOR, 580 kHz SWITCHING FREQ-MAX, PSFM7
封裝: PLASTIC, TO-220, 7 PIN
文件頁數: 7/16頁
文件大?。?/td> 320K
代理商: LT1371IT7
7
LT1371
APPLICATIU
Unique error amplifier circuitry allows the LT1371 to
directly regulate negative output voltages. The negative
feedback amplifier’s 100k source resistor is brought out
for negative output voltage sensing. The NFB pin regulates
at –2.49V while the amplifier output internally drives the
FB pin to 1.245V. This architecture, which uses the same
main error amplifier, prevents duplicating functions and
maintains ease of use. Consult LTC Marketing for units
that can regulate down to –1.25V.
The error signal developed at the amplifier output is
brought out externally. This pin (V
C
) has three different
U
W
U
functions. It is used for frequency compensation, current
limit adjustment and soft starting. During normal regula-
tor operation this pin sits at a voltage between 1V (low
output current) and 1.9V (high output current). The error
amplifier is a current output (g
m
) type, so this voltage can
be externally clamped for lowering current limit. Like-
wise, a capacitor coupled external clamp will provide soft
start. Switch duty cycle goes to zero if the V
C
pin is pulled
below the control pin threshold, placing the LT1371 in an
idle mode.
Positive Output Voltage Setting
The LT1371 develops a 1.245V reference (V
REF
) from the
FB pin to ground. Output voltage is set by connecting the
FB pin to an output resistor divider (Figure 1). The FB pin
bias current represents a small error and can usually be
ignored for values of R2 up to 7k. The suggested value for
R2 is 6.19k. The NFB pin is normally left open for positive
output applications. Positive fixed voltage versions are
available (consult LTC Marketing).
Negative Output Voltage Setting
The LT1371 develops a –2.49V reference (V
NFR
) from the
NFB pin to ground. Output voltage is set by connecting the
NFB pin to an output resistor divider (Figure 2). The
–30
μ
A NFB pin bias current (I
NFB
) can cause output
voltage errors and should not be ignored. This has been
accounted for in the formula in Figure 2. The suggested
value for R2 is 2.49k. The FB pin is normally left open for
negative output applications. See Dual Polarity Output
Voltage Sensing for limitations on FB pin loading when
using the NFB pin.
Dual Polarity Output Voltage Sensing
Certain applications benefit from sensing both positive
and negative output voltages. One example is the “Dual
Output Flyback Converter with Overvoltage Protection”
circuit shown in the Typical Applications section. Each
output voltage resistor divider is individually set as de-
scribed above. When both the FB and NFB pins are used,
R1
V
OUT
= V
REF
1 +
R2
FB
PIN
V
REF
V
OUT
(
)
R1
R2
R1 = R2
– 1
(
)
V
OUT
1.245
LT1371 F01
the LT1371 acts to prevent either output from going
beyond its set output voltage. For example, in this applica-
tion if the positive output were more heavily loaded than
the negative, the negative output would be greater and
would regulate at the desired set-point voltage. The posi-
tive output would sag slightly below its set-point voltage.
This technique prevents either output from going unregu-
lated high at no load. Please note that the load on the FB
pin should not exceed 250
μ
A when the NFB pin is used.
This situation occurs when the resistor dividers are used
at bothFB and NFB. True load on FB is not the full divider
current unless the positive output is shorted to ground.
See Dual Output Flyback Converter application.
APPLICATIU
U
W
U
Figure 1. Positive Output Resistor Divider
Figure 2. Negative Output Resistor Divider
R1
–V
OUT
= V
NFB
+ I
NFB
(R1)
1 +
R2
LT1371 F02
NFB
PIN
V
NFR
I
NFB
–V
OUT
(
)
R1
R2
R1 =
+ 30 10
–6
V
OUT
– 2.49
) (
(
)
2.49
R2
相關PDF資料
PDF描述
LT1371 500kHz High Efficiency 3A Switching Regulator(500kHz ,3A,高效率開關穩壓器)
LT1372CN8 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LT1377IS8 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LT1377 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LT1377CS8 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
相關代理商/技術參數
參數描述
LT1371IT7#PBF 功能描述:IC REG MULTI CONFIG ADJ TO220-7 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓(升壓) 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型,TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT
LT1372 制造商:LINER 制造商全稱:Linear Technology 功能描述:4.5A, 500kHz Step-Down Switching Regulator
LT13725T0050JBK 制造商:American Technical Ceramics Corp 功能描述:LEADED CHIP TERMINATIONS WITH 50 OHM NOMINAL IMPEDENCE
LT1372CN8 功能描述:IC REG MULTI CONFIG ADJ 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓(升壓) 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型,TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT
LT1372CN8#PBF 功能描述:IC REG MULTI CONFIG ADJ 8DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓(降壓) 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON(1.45x1) 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2