參數資料
型號： LT1308BCF#TRPBF
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： 4.5 A SWITCHING REGULATOR, 750 kHz SWITCHING FREQ-MAX, PDSO14
封裝： 4.40 MM, LEAD FREE, PLASTIC, TSSOP-14
文件頁數： 19/20頁
文件大小： 367K
代理商： LT1308BCF#TRPBF
LT1308A/LT1308B
8
1308abfb
OPERATION
The LT1308A combines a current mode, xed frequency
PWM architecture with Burst Mode micropower opera-
tion to maintain high efciency at light loads. Operation
can be best understood by referring to the block diagram
in Figure 2. Q1 and Q2 form a bandgap reference core
whose loop is closed around the output of the converter.
When VIN is 1V, the feedback voltage of 1.22V, along with
an 80mV drop across R5 and R6, forward biases Q1 and
Q2’s base collector junctions to 300mV. Because this is not
enough to saturate either transistor, FB can be at a higher
voltage than VIN. When there is no load, FB rises slightly
above 1.22V, causing VC (the error amplier’s output) to
decrease. When VC reaches the bias voltage on hyster-
etic comparator A1, A1’s output goes low, turning off
all circuitry except the input stage, error amplier and
low-battery detector. Total current consumption in this
state is 140μA. As output loading causes the FB voltage to
decrease, A1’s output goes high, enabling the rest of the IC.
Switch current is limited to approximately 400mA initially
after A1’s output goes high. If the load is light, the output
voltage (and FB voltage) will increase until A1’s output goes
low, turning off the rest of the LT1308A. Low frequency
ripple voltage appears at the output. The ripple frequency
is dependent on load current and output capacitance.
This Burst Mode operation keeps the output regulated
and reduces average current into the IC, resulting in high
efciency even at load currents of 1mA or less.
If the output load increases sufciently, A1’s output
remains high, resulting in continuous operation. When the
LT1308A is running continuously, peak switch current is
controlled by VC to regulate the output voltage. The switch
is turned on at the beginning of each switch cycle. When
the summation of a signal representing switch current
and a ramp generator (introduced to avoid subharmonic
oscillations at duty factors greater than 50%) exceeds the
VC signal, comparator A2 changes state, resetting the ip-
op and turning off the switch. Output voltage increases
as switch current is increased. The output, attenuated
by a resistor divider, appears at the FB pin, closing the
overall loop. Frequency compensation is provided by an
external series RC network connected between the VC pin
and ground.
Low-battery detector A4’s open-collector output (LBO)
pulls low when the LBI pin voltage drops below 200mV.
There is no hysteresis in A4, allowing it to be used as an
amplier in some applications. The entire device is disabled
when the SHDN pin is brought low. To enable the converter,
SHDN must be at 1V or greater. It need not be tied to VIN
as on the LT1308.
The LT1308B differs from the LT1308A in that there is no
hysteresis in comparator A1. Also, the bias point on A1 is
set lower than on the LT1308B so that switching can occur
at inductor current less than 100mA. Because A1 has no
hysteresis, there is no Burst Mode operation at light loads
and the device continues switching at constant frequency.
This results in the absence of low frequency output voltage
ripple at the expense of efciency.
The difference between the two devices is clearly illus-
trated in Figure 3. The top two traces in Figure 3 shows an
LT1308A/LT1308B circuit, using the components indicated
in Figure 1, set to a 5V output. Input voltage is 3V. Load
current is stepped from 50mA to 800mA for both circuits.
Low frequency Burst Mode operation voltage ripple is
observed on Trace A, while none is observed on Trace B.
At light loads, the LT1308B will begin to skip alternate cycles.
The load point at which this occurs can be decreased by
increasing the inductor value. However, output ripple will
continue to be signicantly less than the LT1308A output
ripple. Further, the LT1308B can be forced into micropower
mode, where IQ falls from 3mA to 200μA by sinking 40μA
or more out of the VC pin. This stops switching by causing
A1’s output to go low.
APPLICATIONS INFORMATION
Figure 3. LT1308A Exhibits Burst Mode Operation Output
Voltage Ripple at 50mA Load, LT1308B Does Not
1308 F03
VIN = 3V
(CIRCUIT OF FIGURE 1)
800mA
50mA
TRACE A: LT1308A
VOUT, 100mV/DIV
AC COUPLED
TRACE B: LT1308B
VOUT, 100mV/DIV
AC COUPLED
200μs/DIV
ILOAD
相關PDF資料
PDF描述
LT1937ES5#PBF 0.32 A SWITCHING REGULATOR, 1600 kHz SWITCHING FREQ-MAX, PDSO5
LT1937ES5#TR 0.32 A SWITCHING REGULATOR, 1600 kHz SWITCHING FREQ-MAX, PDSO5
LT1937ESC6#PBF 0.32 A SWITCHING REGULATOR, 1600 kHz SWITCHING FREQ-MAX, PDSO6
LT3484EDCB-0#PBF SPECIALTY ANALOG CIRCUIT, PDSO6
LT3484EDCB-2#PBF SPECIALTY ANALOG CIRCUIT, PDSO6
相關代理商/技術參數
參數描述
LT1308BCS8 功能描述:IC REG BOOST 5V 1A 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤
LT1308BCS8#PBF 功能描述:IC REG BOOST 5V 1A 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2
LT1308BCS8#PBF 制造商:Linear Technology 功能描述:Switching Regulator IC 制造商:Linear Technology 功能描述:IC, DC/DC CONVERTER, 8-SOIC
LT1308BCS8#TR 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Up 0.92V to 10V 8-Pin SOIC N T/R
LT1308BCS8#TRPBF 功能描述:IC REG BOOST 5V 1A 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*