- 您現在的位置：買賣IC網 > PDF目錄377696 > LT1259IN (LINEAR TECHNOLOGY CORP) Low Cost Dual and Triple 130MHz Current Feedback Amplifiers with Shutdown PDF資料下載
參數資料
| 型號： | LT1259IN |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | Low Cost Dual and Triple 130MHz Current Feedback Amplifiers with Shutdown |
| 中文描述： | DUAL OP-AMP, 16000 uV OFFSET-MAX, 130 MHz BAND WIDTH, PDIP14 |
| 封裝： | 0.300 INCH, PLASTIC, DIP-14 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 319K |
| 代理商： | LT1259IN |
7
LT1259/LT1260
Feedback Resistor Selection
The small-signal bandwidth of the LT1259/ LT1260 are set
by the external feedback resistors and the internal junction
capacitors. As a result, the bandwidth is a function of the
supply voltage, the value of the feedback resistor, the
closed-loop gain and the load resistor. The LT1259/LT1260
have been optimized for
±
5V supply operation and have a
–3dB bandwidth of 90MHz. See resistor selection guide in
Typical AC Performance table.
Capacitance on the Inverting Input
Current feedback amplifiers require resistive feedback
from the output to the inverting input for stable operation.
Take care to minimize the stray capacitance between the
output and the inverting input. Capacitance on the invert-
ing input to ground will cause peaking in the frequency
response (and overshoot in the transient response). See
the section on Demo Board Information.
Capacitive Loads
The LT1259/LT1260 can drive capacitive loads directly
when the proper value of feedback resistor is used. The
graph of Maximum Capacitive Load vs Feedback Resistor
should be used to select the appropriate value. The value
shown is for
≤
5dB peaking when driving a 150
load at a
gain of 2. This is a worst case condition. The amplifier is
more stable at higher gains. Alternatively, a small resistor
(10
to 20
) can be put in series with the output to isolate
the capacitive load from the amplifier output. This has the
advantage that the amplifier bandwidth is only reduced
when the capacitive load is present. The disadvantage is
that the gain is a function of the load resistance.
Power Supplies
The LT1259/LT1260 will operate from single or split
supplies from
±
2V (4V total) to
±
15V (30V total). It is not
necessary to use equal value split supplies, however the
offset voltage and inverting input bias current will change.
The offset voltage changes about 500
μ
V per volt of
supply mismatch. The inverting bias current can change
as much as 5
μ
A per volt of supply mismatch though
typically, the change is about 0.1
μ
A per volt.
Slew Rate
The slew rate of a current feedback amplifier is not
independent of the amplifier gain configuration the way
slew rate is in a traditional op amp. This is because both the
input stage and the output stage have slew rate limitations.
In the inverting mode, and for higher gains in the nonin-
verting mode, the signal amplitude between the input pins
is small and the overall slew rate is that of the output stage.
For gains less than ten in the noninverting mode, the
overall slew rate is limited by the input stage.
EN
+IN
–IN
OUT
V
+
V
–
LT1259/60 SS
, each amplifier
SW
W
APPLICATIOU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LT1259IS | Low Cost Dual and Triple 130MHz Current Feedback Amplifiers with Shutdown |
| LT1268BCQ | 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C |
| LT1268BCT | Quad 2-input positive-NAND buffers 14-SO 0 to 70 |
| LT1268CQ | 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C |
| LT1268CT | Quad 2-input positive-NAND buffers with open collector outputs 14-SOIC 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1259IN#PBF | 功能描述:IC AMP DUAL CURR FDBK SHDN 14DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:帶卷 (TR) |
| LT1259IS | 功能描述:IC AMP DUAL CURR FDBK SD 14SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:100 系列:- 放大器類型:通用 電路數:1 輸出類型:- 轉換速率:0.2 V/µs 增益帶寬積:- -3db帶寬:- 電流 - 輸入偏壓:100pA 電壓 - 輸入偏移:30µV 電流 - 電源:380µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):±2 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:管件 |
| LT1259IS#PBF | 功能描述:IC AMP DUAL CURR FDBK SD 14SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:100 系列:- 放大器類型:通用 電路數:1 輸出類型:- 轉換速率:0.2 V/µs 增益帶寬積:- -3db帶寬:- 電流 - 輸入偏壓:100pA 電壓 - 輸入偏移:30µV 電流 - 電源:380µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):±2 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:管件 |
| LT1259IS#TR | 功能描述:IC AMP DUAL CURR FDBK SD 14SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:100 系列:- 放大器類型:通用 電路數:1 輸出類型:- 轉換速率:0.2 V/µs 增益帶寬積:- -3db帶寬:- 電流 - 輸入偏壓:100pA 電壓 - 輸入偏移:30µV 電流 - 電源:380µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):±2 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:管件 |
| LT1259IS#TRPBF | 功能描述:IC AMP DUAL CURR FDBK SD 14SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:100 系列:- 放大器類型:通用 電路數:1 輸出類型:- 轉換速率:0.2 V/µs 增益帶寬積:- -3db帶寬:- 電流 - 輸入偏壓:100pA 電壓 - 輸入偏移:30µV 電流 - 電源:380µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):±2 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。