- 您現在的位置：買賣IC網 > PDF目錄377695 > LT1239CS (LINEAR TECHNOLOGY CORP) Backup Battery Management Circuit PDF資料下載
參數資料
| 型號： | LT1239CS |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Backup Battery Management Circuit |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| 封裝： | 0.150 INCH, PLASTIC, SOP-16 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 246K |
| 代理商： | LT1239CS |
7
LT1239
Comparator:
The output of the comparator is connected to
the output of regulator 2. This point provides power to
memory and power management circuitry. The compara-
tor looks at the main 5V power line and the output voltage
of regulator 2. If the main 5V line is up and regulating the
comparator output will pull up to 5V and supply power to
the memory from the main 5V regulator. If the main 5V
power line drops below 4.85V the comparator switches off
and regulator 2 will supply power to the memory from the
backup batteries. The comparator is powered from the raw
battery voltage at the input of regulator 1.
Error Amplifier:
The Error Amplifier is used to equalize the
cell voltages of two lithium-ion cells connected in series.
The error amplifier is designed to source or sink 5mA.
Low-Battery Detector:
The low-battery detector circuit
acts as an undervoltage lockout. This circuit turns regula-
tor 2 and the error amplifier off if the backup battery
voltage drops below 5V. The low-battery detector circuit
will turn regulator 2 and the error amplifier back on when
the backup battery voltage rises above 5.3V. This circuit
has a quiescent current of approximately 3
μ
A in the
undervoltage condition.
Regulator 2:
Regulator 2 is used to regulate the voltage of
the backup batteries and isolate the backup batteries from
the main 5V line. This regulator will prevent reverse
current flow from the main 5V supply back into the backup
cells.
BLOCK DIAGRA
M
W
APPLICATIO
S I
N
FOR
ATIO
U
Device Overview
The LT1239 provides several functions needed for backup
battery management. It provides:
1. Battery Charging: The LT1239 can be set up to charge
lithium-ion or nickel cadmium batteries in either con-
stant voltage or constant current mode.
2. Memory Power Control: The LT1239 provides power
for the memory and includes automatic switchover
W
U
between the backup battery and the main 5V system
power. When the 5V system supply is up and running it
is used to power the memory, the regulator prevents
reverse current flow back into the backup battery.
Automatic switchover occurs when the 5V system
supply drops below 4.85V and the regulator then pro-
vides power to the memory from the backup cells.
Memory power is uniterruptable.
E/A (IN)
E/A (OUT)
OUT 1
I
MON1
SHDN1
INPUT 2
ADJUST
INPUT 1
IN
IN
2
4
15
10
8
7
14
16
1
13 5V
IN
GROUND PINS 2, 4, 5 ARE TIED TO SUBSTRATE
1239 BD
GND
3
OUT 2
12
REGULATOR
1
I
MON2
SHDN2
5
11
GND
6
–
+
–
+
E/A
REGULATOR
2
INPUT 1
COMP
POWER
SWITCH
LOW-BATTERY
DETECTOR
FU
CTIO
AL DESCRIPTIO
U
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LT1249IN8 | THERMISTOR PTC 1KOHM 100DEG 0805 |
| LT1249CS8 | Power Factor Controller |
| LT1249 | Octal D-Type Edge Triggered Flip-Flops with 3-State Outputs 20-SSOP 0 to 70 |
| LT1249C | Octal D-Type Edge Triggered Flip-Flops with 3-State Outputs 20-SOIC 0 to 70 |
| LT1249I | Octal D-Type Edge Triggered Flip-Flops with 3-State Outputs 20-SOIC 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT123A | 制造商:LINER 制造商全稱:Linear Technology 功能描述:5 Volt, 3 Amp Voltage Regulator |
| LT123AK | 制造商:LINER 制造商全稱:Linear Technology 功能描述:5 Volt, 3 Amp Voltage Regulator |
| LT123AK/883 | 制造商:Linear Technology 功能描述: |
| LT123K | 制造商:LINER 制造商全稱:Linear Technology 功能描述:5 Volt, 3 Amp Voltage Regulator |
| LT1240-7 | 制造商:Power-One 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。