- 您現在的位置：買賣IC網 > PDF目錄377692 > LT1186FCS (LINEAR TECHNOLOGY CORP) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF資料下載
參數資料
| 型號： | LT1186FCS |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | 3 A FLUORESCENT LIGHT CONTROLLER, 240 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | 0.150 INCH, PLASTIC, SO-16 |
| 文件頁數： | 14/16頁 |
| 文件大小： | 206K |
| 代理商： | LT1186FCS |
14
LT1186F
APPLICATIO
S I
FOR
ATIO
U
lation due to its shunt capacitance. Use a decoupling
resistor of several kilohms between the I
CCFL
pin and the
I
OUT
pin if excessive trace stray capacitance exists. Nor-
mally, this resistor is not required.
In some applications, the maximum programming current
required at the I
CCFL
pin for a maximum lamp current will be
less than the full-scale output current of the DAC, which is
50
μ
A. The system designer can either limit the maximum
programming current through software built into the system,
or use a current splitter which shunts a percentage of the full-
scale current from the I
CCFL
pin. A splitter circuit is illustrated
in Figure 3. A divider string is used from a reference voltage
to set up a voltage level equal to the I
CCFL
summing voltage,
or 465mV. The main current flowing in the divider string
should be chosen to swamp out the effects of the shunted
current into the divider string.
W
U
U
The transfer function between lamp current and input
programming current must be empirically determined and
is dependent on the particular lamp/display housing com-
bination used. The lamp and display housing are a distrib-
uted loss structure due to parasitic lamp-to-frame capaci-
tance. This means that the current flowing at the high-
voltage side of the lamp is higher than what is flowing at
the DIO pin side of the lamp. The input programming
current is set to control lamp current at the high-voltage
side of the lamp, even though the feedback signal is the
lamp current at the bottom of the lamp. This ensures that
the lamp is not overdriven which can degrade the lamp’s
operating lifetime. Therefore, the full scale current of the
DAC does not necessarily correspond to the current re-
quired to set maximum lamp current.
Floating Lamp Configuration
In a floating lamp configuration, the lamp is fully floating
with no galvanic connection to ground. This allows the
transformer to provide symmetric differential drive to the
lamp. Balanced drive eliminates the field imbalance asso-
ciated with parasitic lamp-to-frame capacitance and re-
duces “thermometering” (uneven lamp intensity along the
lamp length) at low lamp currents.
Carefully evaluate display designs in relation to the physi-
cal layout of the lamp, its leads and the construction of the
display housing. Parasitic capacitance from any high
voltage point to DC or AC ground creates paths for
unwanted current flow. This parasitic current flow de-
grades electrical efficiency and losses up to 25% have
been observed in practice. As an example, at a Royer
operating frequency of 60kHz, 1pF of stray capacitance
represents an impedance of 2.65M
. With an operating
lamp voltage of 400V and an operating lamp current of
6mA, the parasitic current is 150
μ
A. This additional cur-
rent must be supplied by the transformer secondary.
Layout techniques that increase parasitic capacitance
include long high voltage lamp leads, reflective metal foil
around the lamp and displays supplied in metal enclo-
sures. Losses for a good display are under 5%, whereas,
losses for a bad display range from 5% to 25%. Lossy
displays are the primary reason to use a floating lamp
configuration. Providing symmetric, differential drive to
the lamp reduces the total parasitic loss by one-half.
I
OUT
FULL-SCALE
50
μ
A
V(I
)
465mV
I
XI
V1
R1
V
REF
R3
V(I
CCFL
)
I = 50
μ
A
0 < X < 1
SELECT V1 WITHIN THE DAC I
OUT
COMPLIANCE RANGE
(EX. V1 = 2V FOR V
CC
= 3.3V OR 5V)
CHOOSE I1 >> (1 – X)I
R1 = (V1 – 0.465)/(X)(50
μ
A)
R2 = (V1 – 0.465)/(1 – X)(50
μ
A)
R3 = (V
– 0.465)/I1
R4 = 0.465R3/[(1 – X) 50
μ
AR3
+ (V
REF
– 0.465)]
I1
LT1186F F03
R4
(1 – X)I
R2
Figure 3
Grounded Lamp Configuration
In a grounded lamp configuration, the low voltage side of
the lamp connects directly to the LT1186F DIO pin. This
pin is the common connection between the cathode and
anode of two internal diodes. In previous grounded lamp
solutions, these diodes were discrete units and are now
integrated onto the IC, saving cost and board space.
Bidirectional lamp current flows in the DIO pin and thus,
the diodes conduct alternately on half cycles. Lamp cur-
rent is controlled by monitoring one-half of the average
lamp current. The diode conducting on negative half
cycles has one-tenth of its current diverted to the CCFL pin
and nulls against the source current provided by the lamp
current programmer circuit. The compensation capacitor
on the CCFL V
C
pin provides stable loop compensation and
an averaging function to the rectified sinusoidal lamp
current. Therefore, input programming current relates to
one-half of average lamp current.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1186F | 9-Bit Odd/Even Parity Generators/Checkers 14-PDIP 0 to 70 |
| LT1186FC | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LT1186FI | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LT1186FIS | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LT1187CJ8 | Low Power Video Difference Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1186FCS#PBF | 功能描述:IC SWTCH REG CCFL DAC PROG16SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 照明，鎮流器控制器 系列:Bits-to-Nits™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:CCFL 控制器 頻率:40 ~ 80 kHz 電流 - 電源:5mA 電流 - 輸出:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) 其它名稱:90-3991V+V01 |
| LT1186FCS#TR | 功能描述:IC REG SW CCFL DAC PROG 16SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 照明，鎮流器控制器 系列:Bits-to-Nits™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:CCFL 控制器 頻率:40 ~ 80 kHz 電流 - 電源:5mA 電流 - 輸出:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) 其它名稱:90-3991V+V01 |
| LT1186FCS#TRPBF | 功能描述:IC SW REG CCFL DAC PROG 16SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 照明，鎮流器控制器 系列:Bits-to-Nits™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:CCFL 控制器 頻率:40 ~ 80 kHz 電流 - 電源:5mA 電流 - 輸出:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) 其它名稱:90-3991V+V01 |
| LT1186FIS | 功能描述:IC SWTCH REG CCFL DAC PROG16SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 照明，鎮流器控制器 系列:Bits-to-Nits™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:CCFL 控制器 頻率:40 ~ 80 kHz 電流 - 電源:5mA 電流 - 輸出:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) 其它名稱:90-3991V+V01 |
| LT1186FIS#PBF | 功能描述:IC SW REG CCFL DAC PROG 16SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 照明，鎮流器控制器 系列:Bits-to-Nits™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:CCFL 控制器 頻率:40 ~ 80 kHz 電流 - 電源:5mA 電流 - 輸出:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) 其它名稱:90-3991V+V01 |
發布緊急采購，3分鐘左右您將得到回復。