- 您現在的位置：買賣IC網 > PDF目錄377692 > LT1185IT (LINEAR TECHNOLOGY CORP) 9-Bit Odd/Even Parity Generators/Checkers 14-SOIC 0 to 70 PDF資料下載
參數資料
| 型號： | LT1185IT |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 9-Bit Odd/Even Parity Generators/Checkers 14-SOIC 0 to 70 |
| 中文描述： | 2.5 V-25 V ADJUSTABLE NEGATIVE LDO REGULATOR, 1 V DROPOUT, PSFM5 |
| 封裝： | PLASTIC, TO-220, 5 PIN |
| 文件頁數： | 8/16頁 |
| 文件大?。?/td> | 211K |
| 代理商： | LT1185IT |
8
LT1185
APPLICATIU
factor is that local ambient temperature may be somewhat
higher because of the point source of heat. The conse-
quences of excess junction temperature include poor
reliability, especially for plastic packages, and the possi-
bility of thermal shutdown or degraded electrical charac-
teristics. The final design should be checked in situwith a
thermocouple attached to the regulator case under worst-
case conditions of high ambient, high input voltage and
full load.
U
W
U
What About Overloads
IC regulators with thermal shutdown, like the LT1185,
allow heat sink designs which concentrate on worst-case
“normal” conditions and ignore “fault” conditions. An
output overload or short may force the regulator to exceed
its maximum junction temperature rating, but thermal
shutdown is designed to prevent regulator failure under
these conditions. A word of caution however; thermal
shutdown temperatures are typically 175
°
C in the control
portion of the die and 180
°
C to 225
°
C in the power
transistor section. Extended operation at these tempera-
tures can cause permanent degradation of plastic encap-
sulation. Designs which may be subjected to extended
periods of overload should either use the hermetic TO-3
package or increase heat sink size. Foldback current
limiting can be implemented to minimize power levels
under fault conditions.
External Current Limit
The LT1185 requires a resistor to set current limit. The
value of this resistor is 15k divided by the desired current
limit (in amps). The resistor for 2A current limit would be
15k/2A = 7.5k. Tolerance over temperature is
±
10%, so
current limit is normally set 15% above maximum load
current. Foldback limiting can be employed if short-circuit
current must be lower than full load current (see Typical
Applications).
The LT1185 has internal current limiting which will over-
ride external current limit if power in the pass transistor is
excessive. The internal limit is
≈
3.6A with a foldback
characteristic which is dependent on input-output voltage,
not output voltage per se(see Typical Performace Charac-
teristics).
Ground Pin Current
Ground pin current for the LT1185 is approximately 2mA
plus I
OUT
/40. At I
OUT
= 3A, ground pin current is typically
2mA + 3/40 = 77mA. Worst case guarantees on the ratio of
I
OUT
to ground pin current are contained in the Electrical
Specifications.
Ground pin current can be important for two reasons. It
adds to power dissipation in the regulator and it can affect
load/line regulation if a long line is run from the ground pin
to load ground. The additional power dissipation is found
by multiplying ground pin current by input voltage. In a
typical example, with V
IN
= 8V, V
OUT
= 5V and I
OUT
= 2A, the
LT1185 will dissipate (8V – 5V)(2A) = 6W in the pass
transistor and (2A/40)(8V) = 0.4W in the internal drive
circuitry. This is only a 1.5% efficiency loss, and a 6.7%
increase in regulator power dissipation, but these values
will increase at higher output voltages.
Ground pin current can affect regulation as shown in
Figure 2. Parasitic resistance in the ground pin lead will
create a voltage drop which increasesoutput voltage as
load current is increased. Similarly, output voltage can
decreaseas input voltage increases because the “I
OUT
/40”
component of ground pin current drops significantly at
higher input-output differentials. These effects are small
enough to be ignored for local regulation applications, but
for remote sense applications, they may need to be consid-
ered. Ground lead resistance of 0.4
would cause an
output voltage error of up to (3A/40)(0.4
) = 30mV, or
0.6% at V
OUT
= 5V. Note that if the sense leads are
connected as shown in Figure 2, with r
a
≈
0
, this error is
a fixed number of millivolts, and does not increase as a
function of DC output voltage.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1185M | 9-Bit Odd/Even Parity Generators/Checkers 14-SOIC 0 to 70 |
| LT1185MK | 9-Bit Odd/Even Parity Generators/Checkers 14-SOIC 0 to 70 |
| LT1185 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| LT1186 | 9-Bit Odd/Even Parity Generators/Checkers 14-SOIC 0 to 70 |
| LT1186FCS | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1185IT#06 | 制造商:Linear Technology 功能描述:Low Dropout Regulator |
| LT1185IT#06PBF | 功能描述:IC REG LDO NEG ADJ 3A TO220-5 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:3V 輸入電壓:2.3 V ~ 5.5 V 電壓 - 壓降（標準）:0.035V @ 150mA 穩壓器數量:2 電流 - 輸出:150mA 電流 - 限制（最?。?300mA 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 裸露焊盤，6-TMLF? 供應商設備封裝:6-TMLF?（1.6x1.6） 包裝:Digi-Reel® 產品目錄頁面:1104 (CN2011-ZH PDF) 其它名稱:576-3018-6 |
| LT1185IT#06PBF | 制造商:Linear Technology 功能描述:VOLTAGE REGULATOR LDO ADJ 3 制造商:Linear Technology 功能描述:VOLTAGE REGULATOR, LDO, ADJ, 3A, TO-220- |
| LT1185IT#30PBF | 功能描述:IC REG LDO NEG ADJ 3A TO220-5 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:3,000 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:2.5V 輸入電壓:2.5 V ~ 5.5 V 電壓 - 壓降（標準）:- 穩壓器數量:1 電流 - 輸出:300mA（最小值） 電流 - 限制（最小）:360mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 供應商設備封裝:TSOT-23-5 包裝:帶卷 (TR) |
| LT1185IT#31 | 制造商:Linear Technology 功能描述:LDO Regulator Neg/Pos 2.5V to 25V-2.5V to -25V 3A 5-Pin(5+Tab) TO-220 |
發布緊急采購，3分鐘左右您將得到回復。