- 您現在的位置：買賣IC網 > PDF目錄377690 > LT1173CN8-5 (LINEAR TECHNOLOGY CORP) Micropower DC/DC Converter Adjustable and Fixed 5V, 12V PDF資料下載
參數資料
| 型號： | LT1173CN8-5 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Micropower DC/DC Converter Adjustable and Fixed 5V, 12V |
| 中文描述： | 1.5 A SWITCHING REGULATOR, 23 kHz SWITCHING FREQ-MAX, PDIP8 |
| 封裝： | MINI, PLASTIC, DIP-8 |
| 文件頁數： | 6/16頁 |
| 文件大小： | 322K |
| 代理商： | LT1173CN8-5 |
LT1173
6
U
S
A
O
PPLICATI
U
U
LT1173 TA06
+
–
SET
V
+12V
+
μ
1 F*
μ
1000 F
100
V1
V2
LTC1050
1M
LT1173
CIRCUIT
*NON-POLARIZED
Figure 1. Test Circuit Measures No Load Quiescent Current of
LT1073 Converter
Inductor Selection
A DC-DC converter operates by storing energy as mag-
netic flux in an inductor core, and then switching this
energy into the load. Since it is flux, not charge, that is
stored, the output voltage can be higher, lower, or oppo-
site in polarity to the input voltage by choosing an
appropriate switching topology. To operate as an efficient
energy transfer element, the inductor must fulfill three
requirements. First, the inductance must be low enough
for the inductor to store adequate energy under the worst
case condition of minimum input voltage and switch ON
time. The inductance must also be high enough so that
maximum current ratings of the LT1173 and inductor are
not exceeded at the other worst case condition of maxi-
mum input voltage and ON time. Additionally, the inductor
core must be able to store the required flux; i.e., it must not
saturate At power levels generally encountered with
LT1173 based designs, small axial leaded units with
saturation current ratings in the 300mA to 1A range
(depending on application) are adequate. Lastly, the in-
ductor must have sufficiently low DC resistance so that
excessive power is not lost as heat in the windings. An
additional consideration is Electro-Magnetic Interference
(EMI). Toroid and pot core type inductors are recom-
mended in applications where EMI must be kept to a
minimum; for example, where there are sensitive analog
circuitry or transducers nearby. Rod core types are a less
expensive choice where EMI is not a problem.
Specifying a proper inductor for an application requires
first establishing minimum and maximum input voltage,
output voltage, and output current. In a step-up converter,
the inductive events add to the input voltage to produce the
output voltage. Power required from the inductor is deter-
mined by
P
L
= (V
OUT
+ V
D
– V
IN
) (I
OUT
)
(02)
where V
D
is the diode drop (0.5V for a 1N5818 Schottky).
Energy required by the inductor per cycle must be equal or
greater than
P
F
L
OSC
03
( )
in order for the converter to regulate the output.
When the switch is closed, current in the inductor builds
according to
I
t
V
R
e
L
IN
'
L
( )
=
( )
–
–R t
1
04
where R' is the sum of the switch equivalent resistance
(0.8
typical at 25
°
C) and the inductor DC resistance.
When the drop across the switch is small compared to V
IN
,
the simple lossless equation
I
t
V
L
t
L
IN
( )
=
( )
05
can be used. These equations assume that at t = 0,
inductor current is zero. This situation is called “discon-
tinuous mode operation” in switching regulator parlance.
Setting “t” to the switch ON time from the LT1173 speci-
fication table (typically 23
μ
s) will yield i
PEAK
for a specific
“L” and V
IN
. Once i
PEAK
is known, energy in the inductor at
the end of the switch ON time can be calculated as
E
Li
L
PEAK
=
( )
1
2
06
2
E
L
must be greater than P
L
/F
OSC
for the converter to deliver
the required power. For best efficiency i
PEAK
should be
kept to 1A or less. Higher switch currents will cause
excessive drop across the switch resulting in reduced
efficiency. In general, switch current should be held to as
low a value as possible in order to keep switch, diode and
inductor losses at a minimum.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1173CS8 | Micropower DC/DC Converter Adjustable and Fixed 5V, 12V |
| LT1173CS8-12 | Micropower DC/DC Converter Adjustable and Fixed 5V, 12V |
| LT1173CS8-5 | Micropower DC/DC Converter Adjustable and Fixed 5V, 12V |
| LT1175C | 500mA Negative Low Dropout Micropower Regulator |
| LT1175CQ | 500mA Negative Low Dropout Micropower Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1173CN8-5#PBF | 功能描述:IC REG BUCK BST INV 5V 0.4A 8DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LT1173CN8-5PBF | 制造商:Linear Technology 功能描述:LT1173CN8-5PBF |
| LT1173CN8PBF | 制造商:Linear Technology 功能描述:LT1173CN8PBF |
| LT1173CS8 | 功能描述:IC REG BUCK BOOST INV ADJ 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LT1173CS8#PBF | 功能描述:IC REG BUCK BOOST INV ADJ 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
發布緊急采購，3分鐘左右您將得到回復。