參數資料
型號: LT1128ACN8
廠商: LINEAR TECHNOLOGY CORP
元件分類: 運動控制電子
英文描述: Ultra Low Noise Precision High Speed Op Amps
中文描述: OP-AMP, 80 uV OFFSET-MAX, 20 MHz BAND WIDTH, PDIP8
封裝: 0.300 INCH, PLASTIC, DIP-8
文件頁數: 11/20頁
文件大小: 439K
代理商: LT1128ACN8
11
LT1028/LT1128
U
S
A
O
PPLICATI
U
U
0.1Hz to 10Hz Noise Test Circuit
0.1Hz to 10Hz Peak-to-Peak Noise
Tester Frequency Response
FREQUENCY (Hz)
40
G
60
70
90
100
0.01
1.0
10
100
LT1028/1128 AI03
30
0.1
50
80
+
VOLTAGE GAIN = 50,000
* DEVICE UNDER TEST
NOTE ALL CAPACITOR VALUES ARE FOR
NONPOLARIZED CAPACITORS ONLY
100k
100
+
2k
4.7
μ
F
0.1
μ
F
100k
24.3k
22
μ
F
2.2
μ
F
4.3k
110k
SCOPE
×
1
R
IN
= 1M
0.1
μ
F
*
1028/1128 AI02
LT1001
–U
Noise Testing – Voltage Noise
The LT1028/LT1128's RMS voltage noise density can be
accurately measured using the Quan Tech Noise Analyzer,
Model 5173 or an equivalent noise tester. Care should be
taken, however, to subtract the noise of the source resistor
used. Prefabricated test cards for the Model 5173 set the
device under test in a closed-loop gain of 31 with a 60
source resistor and a 1.8k feedback resistor. The noise of
this resistor combination is 0.13
58 = 1.0nV/
Hz. An
LT1028/LT1128 with 0.85nV/
Hz noise will read (0.85
2
+
1.0
2
)
1/2
= 1.31nV/
Hz. For better resolution, the resistors
should be replaced with a 10
source and 300
feedback
resistor. Even a 10
resistor will show an apparent noise
which is 8% to 10% too high.
The 0.1Hz to 10Hz peak-to-peak noise of the LT1028/
LT1128 is measured in the test circuit shown. The fre-
quency response of this noise tester indicates that the
0.1Hz corner is defined by only one zero. The test time to
measure 0.1Hz to 10Hz noise should not exceed 10
seconds, as this time limit acts as an additional zero to
eliminate noise contributions from the frequency band
below 0.1Hz.
Measuring the typical 35nV peak-to-peak noise perfor-
mance of the LT1028/LT1128 requires special test pre-
cautions:
(a) The device should be warmed up for at least five
minutes. As the op amp warms up, its offset voltage
changes typically 10
μ
V due to its chip temperature
increasing 30
°
C to 40
°
C from the moment the power
supplies are turned on. In the 10 second measure-
ment interval these temperature-induced effects can
easily exceed tens of nanovolts.
(b) For similar reasons, the device must be well shielded
from air current to eliminate the possibility of thermo-
electric effects in excess of a few nanovolts, which
would invalidate the measurements.
(c) Sudden motion in the vicinity of the device can also
“feedthrough” to increase the observed noise.
A noise-voltage density test is recommended when mea-
suring noise on a large number of units. A 10Hz noise-
voltage density measurement will correlate well with a
0.1Hz to 10Hz peak-to-peak noise reading since both
results are determined by the white noise and the location
of the 1/f corner frequency.
相關PDF資料
PDF描述
LT1128AM Ultra Low Noise Precision High Speed Op Amps
LT1128AMJ8 Octal Buffers/Line Drivers with 3-State Outputs 20-SSOP 0 to 70
LT1128C Octal Buffers/Line Drivers with 3-State Outputs 20-SSOP 0 to 70
LT1128M Ultra Low Noise Precision High Speed Op Amps
LT1028CJ8 Ultra Low Noise Precision High Speed Op Amps
相關代理商/技術參數
參數描述
LT1128ACN8#PBF 功能描述:IC OP-AMP LOW NOISE SNGL 8-DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源,單路/雙路(±):4.5 V ~ 38 V,±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC(0.154",3.90mm 寬) 供應商設備封裝:8-SOIC 包裝:帶卷 (TR)
LT1128AM 制造商:LINER 制造商全稱:Linear Technology 功能描述:Ultra Low Noise Precision High Speed Op Amps
LT1128AMJ8 制造商:LINER 制造商全稱:Linear Technology 功能描述:Ultra Low Noise Precision High Speed Op Amps
LT1128C 制造商:LINER 制造商全稱:Linear Technology 功能描述:Ultra Low Noise Precision High Speed Op Amps
LT1128CJ8 制造商:LINER 制造商全稱:Linear Technology 功能描述:Ultra Low Noise Precision High Speed Op Amps