- 您現在的位置：買賣IC網 > PDF目錄377684 > LT1121 (Linear Technology Corporation) Octal Buffers/Drivers With 3-State Outputs 20-SO 0 to 70 PDF資料下載
參數資料
| 型號： | LT1121 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Octal Buffers/Drivers With 3-State Outputs 20-SO 0 to 70 |
| 中文描述： | 微功率低壓差穩壓器，帶有關斷 |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 269K |
| 代理商： | LT1121 |
8
LT1121/LT1121-3.3/LT1121-5
U
S
A
The LT1121 is a micropower low dropout regulator with
shutdown, capable of supplying up to 150mA of output
current at a dropout voltage of 0.4V. The device operates
with very low quiescent current (30
μ
A). In shutdown the
quiescent current drops to only 16
μ
A. In addition to the
low quiescent current the LT1121 incorporates several
protection features which make it ideal for use in battery-
powered systems. The device is protected against both
reverse input voltages and reverse output voltages. In
battery backup applications where the output can be held
up by a backup battery when the input is pulled to ground,
the LT1121 acts like it has a diode in series with its output
and prevents reverse current flow.
O
PPLICATI
U
U
Adjustable Operation
The adjustable version of the LT1121 has an output
voltage range of 3.75V to 20V. The output voltage is set by
the ratio of two external resistors as shown in Figure 1. The
device servos the output voltage to maintain the voltage at
the adjust pin at 3.75V. The current in R1 is then equal to
3.75V/R1. The current in R2 is equal to the sum of the
current in R1 and the adjust pin bias current. The adjust pin
bias current, 150nA at 25
°
C, flows through R2 into the
adjust pin. The output voltage can be calculated according
to the formula in Figure 1. The value of R1 should be less
than 400k to minimize errors in the output voltage caused
by the adjust pin bias current. Note that in shutdown the
output is turned off and the divider current will be zero.
Curves of Adjust Pin Voltage vs Temperature and Adjust
Pin Bias Current vs Temperature appear in the Typical
Performance Characteristics. The reference voltage at the
adjust pin has a slight positive temperature coefficient of
approximately 15ppm/
°
C. The adjust pin bias current has
a negative temperature coefficient. These effects are small
and will tend to cancel each other.
The adjustable device is specified with the adjust pin tied
to the output pin. This sets the output voltage to 3.75V.
Specifications for output voltage greater than 3.75V will be
proportional to the ratio of the desired output voltage to
3.75V (V
OUT
/3.75V). For example: load regulation for an
output current change of 1mA to 150mA is –12mV typical
at V
OUT
= 3.75V. At V
OUT
= 12V, load regulation would be:
12
3 75
.
12
38
V
V
mV
mV
–
–
×
(
)
=
(
)
Thermal Considerations
Power handling capability will be limited by maximum
rated junction temperature (125
°
C). Power dissipated by
the device will be made up of two components:
1. Output current multiplied by the input/output voltage
differential: I
OUT
×
(V
IN
– V
OUT
), and
2. Ground pin current multiplied by the input voltage:
I
GND
×
V
IN
.
The ground pin current can be found by examining the
Ground Pin Current curves in the Typical Performance
Characteristics. Power dissipation will be equal to the sum
of the two components listed above.
The LT1121 series regulators have internal thermal limit-
ing designed to protect the device during overload condi-
tions. For continuous normal load conditions the maxi-
mum junction temperature rating of 125
°
C must not be
exceeded. It is important to give careful consideration to
all sources of thermal resistance from junction to ambient.
Additional heat sources mounted nearby must also be
considered.
Heat sinking, for surface mount devices, is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Copper board stiffeners and plated
through holes can also be used to spread the heat gener-
ated by power devices. Tables 1 through 5 list thermal
resistances for each package. Measured values of thermal
resistance for several different board sizes and copper
areas are listed for each package. All measurements were
Figure 1. Adjustable Operation
IN
LT1121
GND
SHDN
1121 F01
+
ADJ
OUT
R2
R1
V
OUT
= 3.75V 1 + R1
ADJ
R2
V
ADJ
= 3.75V
I
ADJ
= 150nA
AT
25°C
OUTPUT RANGE = 3.75V
TO
30V
(
)
(
)
V
OUT
相關PDF資料 |
PDF描述 |
|---|---|
| LT1121-5 | Octal Buffers/Drivers With 3-State Outputs 20-SO 0 to 70 |
| LT1121CN8 | Octal Buffers/Drivers With 3-State Outputs 20-SOIC 0 to 70 |
| LT1121CN8-5 | Octal Buffers/Drivers With 3-State Outputs 20-SOIC 0 to 70 |
| LT1121CS8 | Octal Buffers/Drivers With 3-State Outputs 20-SOIC 0 to 70 |
| LT1121CS8-5 | Octal Buffers/Drivers With 3-State Outputs 20-SOIC 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1121_07 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower Low Dropout Regulators with Shutdown |
| LT1121_12 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower Low Dropout Regulators with Shutdown |
| LT1121-3.3 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower Low Dropout Regulators with Shutdown |
| LT1121-5 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower Low Dropout Regulators with Shutdown |
| LT1121ACS8 | 功能描述:IC REG LDO ADJ .15A 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 產品培訓模塊:More Information on LDOs 標準包裝:50 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:3.3V 輸入電壓:最高 15V 電壓 - 壓降（標準）:1.1V @ 800mA 穩壓器數量:1 電流 - 輸出:800mA 電流 - 限制（最?。?800mA 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-4，D²Pak（3 引線+接片），TO-263AA 供應商設備封裝:D2PAK-3 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。