- 您現在的位置：買賣IC網 > PDF目錄377684 > LT1118-2.5 (Linear Technology Corporation) Low IQ, Low Dropout, 800mA, Source and Sink Regulators Adjustable and Fixed 2.5V, 2.85V, 5V Output PDF資料下載
參數資料
| 型號： | LT1118-2.5 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Low IQ, Low Dropout, 800mA, Source and Sink Regulators Adjustable and Fixed 2.5V, 2.85V, 5V Output |
| 中文描述： | 低智商，低壓差，800mA電流源庫調節可調和固定為2.5V，工作在2.85V，5V輸出 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 109K |
| 代理商： | LT1118-2.5 |
5
LT1118/LT1118-2.5
LT1118-2.85/LT1118-5
PI
FU
CTIO
N
S
U
U
IN:
Input Supply Pin. This pin should be decoupled with a
1
μ
F or larger low ESR capacitor. The two IN pins on the
SO-8 package must be directly connected on the printed
circuit board to prevent voltage drops between the two
inputs. When used as a SCSI active termination, IN con-
nects to term power. When used as a supply splitter, IN is
also the positive supply output.
GND:
Ground Pin. The multiple GND pins on the SO-8
package are internally connected, but lowest load regula-
tion errors will result if these pins are tightly connected on
the printed circuit board. This will also aid heat dissipation
at high power levels.
EN:
TTL/CMOS Logic Input. A high level allows normal
operation. A low level reduces supply current to zero. This
pin is internally connected to V
IN
on 3-lead ST packaged
devices.
OUT:
Regulated Output Voltage. Output can source or sink
current. Current limit for sourcing and sinking current is
provided to protect the device from fault conditons. The
output must have a low ESR output filter capacitor. C
OUT
≥
0.22
μ
F to guarantee stability. A 0.1
μ
F ceramic capacitor
may be needed in parallel with C
OUT
if the ESR of the main
C
OUT
is too high.
FB:
Feedback Pin. The feedback pin is used to program the
output voltage of the adjustable S8 part. The output
voltage is determined by the selection of feedback resis-
tors defined by the following formula:
V
OUT
= V
FB
(1 + R
1
/R
2
) + I
FB
R
1
LT1118 Adjustable
GND
IN
OUT
EN
FB
R
1
R
2
1
μ
F
V
IN
1118 TA06
LT1118
1
μ
F
R
1
R
2
1 +
V
OUT
= V
FB
+ I
FB
R
1
(
)
OPERATIOU
Output Capacitor
The LT1118 family of voltage regulators require an output
capacitor for stability. The regulators are stable with
output capacitors larger than 0.2
μ
F. Load transient re-
sponse is very sensitive to output capacitor value and
dielectric choice. Low ESR ceramic capacitors are the best
choice for fast settling to load transients. Output capaci-
tors between 0.2
μ
F and 1
μ
F give good performance in
most applications. Larger tantalum output capacitors may
be used to reduce load transient amplitudes. Larger ca-
pacitors should be paralleled with a 0.1
μ
F ceramic capaci-
tor to maintain quick settling time performance and to
insure stability of the regulator control loop. Capacitors
larger than 10
μ
F may be safely used with the regulators,
but little transient settling performance improvement re-
sults from their use.
Worst case transient response of the LT1118 regulators
occurs at zero output current. In order to obtain the fastest
transient settling performance, the regulator output may
be preloaded with a small current. The preload current
reduces the regulator output impedance, reducing output
voltage settling time.
Thermal Considerations
The LT1118 regulators are packaged in plastic SOT-223
and fused lead S8 packages. These small footprint pack-
ages are unable to convectively dissipate the heat gener-
ated when the regulator is operating at high current levels.
In order to control die operating temperatures, the PC
board layout should allow for maximum possible copper
area at the ground pins of the LT1118. The ground pins
and the tab on the SOT-223 package are electrically and
相關PDF資料 |
PDF描述 |
|---|---|
| LT1118CS8-2.5 | Low IQ, Low Dropout, 800mA, Source and Sink Regulators Adjustable and Fixed 2.5V, 2.85V, 5V Output |
| LT1118 | Low IQ, Low Dropout, 800mA, Source and Sink Regulators Adjustable and Fixed 2.5V, 2.85V, 5V Output |
| LT1118-5 | Low IQ, Low Dropout, 800mA, Source and Sink Regulators Adjustable and Fixed 2.5V, 2.85V, 5V Output |
| LT1118CS8 | Low IQ, Low Dropout, 800mA, Source and Sink Regulators Adjustable and Fixed 2.5V, 2.85V, 5V Output |
| LT1118CS8-2.85 | Low IQ, Low Dropout, 800mA, Source and Sink Regulators Adjustable and Fixed 2.5V, 2.85V, 5V Output |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1118-5 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Low IQ, Low Dropout, 800mA, Source and Sink Regulators Adjustable and Fixed 2.5V, 2.85V, 5V Output |
| LT1118CS8 | 功能描述:IC REG LDO ADJ .8A 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:800 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:2.5V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.7V @ 4A 穩壓器數量:1 電流 - 輸出:4A 電流 - 限制（最小）:4.2A 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6，D²Pak（5 引線+接片），TO-263BA 供應商設備封裝:TO-263-5 包裝:帶卷 (TR) 其它名稱:AP1184K525L-13AP1184K525LDITR |
| LT1118CS8#PBF | 功能描述:IC REG LDO ADJ .8A 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:8V 輸入電壓:10.5 V ~ 23 V 電壓 - 壓降（標準）:1.7V @ 40mA 穩壓器數量:1 電流 - 輸出:100mA（最小值） 電流 - 限制（最?。?- 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:剪切帶 (CT) 產品目錄頁面:1075 (CN2011-ZH PDF) 其它名稱:296-24390-1 |
| LT1118CS8#TR | 功能描述:IC REG LDO ADJ .8A 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:800 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:2.5V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.7V @ 4A 穩壓器數量:1 電流 - 輸出:4A 電流 - 限制（最小）:4.2A 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6，D²Pak（5 引線+接片），TO-263BA 供應商設備封裝:TO-263-5 包裝:帶卷 (TR) 其它名稱:AP1184K525L-13AP1184K525LDITR |
| LT1118CS8#TRPBF | 功能描述:IC REG LDO ADJ .8A 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:800 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:2.5V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.7V @ 4A 穩壓器數量:1 電流 - 輸出:4A 電流 - 限制（最?。?4.2A 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6，D²Pak（5 引線+接片），TO-263BA 供應商設備封裝:TO-263-5 包裝:帶卷 (TR) 其它名稱:AP1184K525L-13AP1184K525LDITR |
發布緊急采購，3分鐘左右您將得到回復。