參數資料
型號： LT1105IN8
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
中文描述： 1.5 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDIP8
封裝： 0.300 INCH, PLASTIC, DIP-8
文件頁數： 15/32頁
文件大?。?/td> 452K
代理商： LT1105IN8
15
LT1103/LT1105
U
ATIO
OPER
Control of output voltage is obtained by using the output
of a voltage sensing error amplifier to set current trip level.
This technique has several advantages. First, it has imme-
diate response to input voltage variations, unlike ordinary
switchers which have notoriously poor line transient re-
sponse. Second, it reduces the 90
°
phase shift at
midfrequencies in the transformer. This greatly simplifies
closed-loop frequency compensation under widely vary-
ing input voltage or output load conditions. Finally, it
allows simple pulse-by-pulse current limiting to provide
maximum switch protection under output overload or
short-circuit conditions.
A start-up loop with hysteresis allows the IC supply
voltage to be bootstrapped from an extra primary side
winding on the power transformer. From 0V to 16V on V
IN
,
the LT1105 is in prestart mode and total input current is
typically 200
μ
A. Above 16V, up to 30V, the 6V regulator
that biases the internal circuitry and the externally avail-
able 5V and 15V regulators are turned on. The internal
circuitry remains biased on until V
IN
drops below 7V and
the part returns to prestart mode. Output switching stops
when the 15V gate bias reference is less than 10V corre-
sponding to V
IN
of about 12V.
The oscillator provides the basic clock for all internal
timing. Frequency is adjustable to 200kHz with one exter-
nal capacitor from OSC to ground. The oscillator turns on
the output switch via the logic and driver circuitry.
The LT1105 is designed to drive the gate of an external
power FET in common source configuration. The drivers
and the 1A maximum totem-pole output stage are biased
from the 15V gate bias reference. Special drive detection
circuity senses the gate bias reference voltage and pre-
vents the output switch from turning on if this voltage is
less than 10V or greater than 20V. Break-Before-Make
action of 200ns is built into each switch edge to eliminate
cross conduction currents.
Switch current is sensed externally through a precision,
power resistor. This allows for greater flexibility in switch
current and output power than allowed by the LT1103. The
voltage across the sense resistor is fed into the I
LIM
pin and
amplified to trip the comparator and turn off the switch
according to the V
C
pin control voltage. A blanking circuit
suppresses the output of the current limit comparator for
500ns at the beginning of each switch cycle. This prevents
false tripping of the comparator due to current spikes
caused by external parasitic capacitance and diode stored
charge.
A 4.5V Zener-based reference biases the positive input of
the sampling error amplifier. The negative input (FB) is
used for output voltage sensing. The sampling error
amplifier allows the LT1105 to operate in fully isolated
flyback mode by regulating the flyback voltage of the
bootstrap winding. The leakage inductance spike at the
leading edge of the flyback waveform is ignored with a
blanking circuit. The flyback waveform is directly propor-
tional to the output voltage in the transformer coupled
flyback topology. Output voltages are fully floating up to
the breakdown voltage of the transformer windings. Mul-
tiple floating outputs are easily obtained with additional
windings.
The error signal developed at the comparator input is
brought out externally. The V
C
pin has three functions
including frequency compensation, current limit adjust-
ment and total regulator shutdown. During normal opera-
tion, this pin sits at a voltage between 1.2V (low output
current) and 4.4V (high output current). The error ampli-
fier is a current output (g
m
) type, so this voltage can be
externally clamped for adjusting current limit. Switch duty
cycle goes to zero if the V
C
pin is pulled to ground through
a diode, placing the LT1105 in an idle mode. Pulling the V
C
pin below 0.15V causes total regulator shutdown and
places the LT1105 in prestart mode.
The SS pin implements soft-start with one external capaci-
tor to ground. The internal pull-up current and clamp
transistor limit the voltage at V
C
to one diode drop above
the voltage at the SS pin, thereby controlling the rate of rise
of switch current in the regulator. The SS pin is reset to 0V
when the LT1105 is in prestart mode.
A final protection feature includes overvoltage lockout
monitoring of the main supply voltage on the OVLO pin. If
the OVLO pin is greater than 2.5V, the output switch is
prevented from turning on. This function can be disabled
by grounding the OVLO pin.
相關PDF資料
PDF描述
LT1105C RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LT1103 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LT1103C RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LT1103CT7 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LT1105 4-Bit Synchronous Up/Down Binary Counters 16-SOIC 0 to 70
相關代理商/技術參數
參數描述
LT1105IN8#PBF 制造商:Linear Technology 功能描述:Conv DC-DC Single 30V 8-Pin PDIP N
LT1106 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower Step-Up DC/DC Converter for PCMCIA Card Flash Memory
LT1106_02 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower Step-Up DC/DC Converter for PCMCIA Card Flash Memory
LT1106CF 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower Step-Up DC/DC Converter for PCMCIA Card Flash Memory
LT1107 制造商: 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*