參數資料
型號： LT1105CN
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
中文描述： 1.5 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDIP14
封裝： 0.300 INCH, PLASTIC, DIP-14
文件頁數： 11/32頁
文件大?。?/td> 452K
代理商： LT1105CN
11
LT1103/LT1105
PI
FU
CTIO
N
S
U
U
LT1103
FB:
The Feedback pin is the inverting input to the sampling
error amplifier. The noninverting input is tied to a 4.5V
reference. The FB pin is used for output voltage sensing.
The input bias current is a function of the control pin V
C
voltage and can be used for load regulation compensation
by including a resistor in series with the FB pin. The
sampling error amplifier has a typical g
m
of 0.012 mhos
and the output of the sampling error amplifier has asym-
metrical slew rate to reduce overshoot during start-up
conditions or following the release of an output overload.
V
C
:
The V
C
control pin is used for frequency compensa-
tion, current limiting and shutdown. It is the high imped-
ance output of the sampling error amplifier and the input
of the current limit comparator.
GND:
The Ground pin acts as both the negative sense
point for the internal sampling error amplifier feedback
signal and as the high current path for the 2A switch.
Also, the case of the 7-lead TO-220 is connected to
ground. Proper connections to ground for signal paths
and high current paths must be made in order to insure
good load regulation.
OSC:
The Oscillator pin sets the operating frequency of the
regulator with one external capacitor to ground. Maximum
duty cycle can also be adjusted by using an external
resistor to alter the charge/discharge ratio.
V
IN
:
The Input Supply pin is designed to operate with
voltages of 12V to 30V. The supply current is typically
200
μ
A up to the start-up threshold of 16V. Normal oper-
ating supply current is fairly flat at 18mA down to the
shutdown threshold of 7V. Switching is inhibited for V
IN
less than 12V due to the gate drive detection circuit.
15V:
A 15V reference is used to bias the gate of an external
power FET. The voltage temperature coefficient is typically
3mV/
°
C and the output can source 30mA. Typical dropout
voltage is 1.5V for V
IN
less than 17V and 30mA of load
current.
V
SW
:
The Switch Output pin is the collector of the internal
NPN power switch. This pin has a typical ON resistance of
0.4
and a minimum breakdown voltage of 50V. This pin
also ties to the FET gate drive detection circuit.
LT1105
All functions on the LT1105 are equivalent to the LT1103
with the exception of the V
SW
pin and the I
LIM
pin and the
availability of the OVLO, 5V, and SS functions.
OVLO:
The Overvoltage Lockout pin inhibits switching
when the pin is pulled above its threshold voltage of 2.5V.
OVLO is implemented with a resistor divider network from
the rectified DC line and is used to protect the external FET
from an overvoltage condition in the off state. This func-
tion is only available on the 14-lead PDIP.
5V:
A 5V reference is available to power primary-side
circuitry. The temperature coefficient is typically
50ppm/
°
C and the output can source 25mA. This func-
tion is only available on the 14-lead PDIP.
SS:
The Soft-Start pin is used to either program start-up
time with a capacitor to ground or to set external current
limit with a resistor divider. The SS pin has a 40
μ
A pull-up
current and is reset to 0V by a 1mA pull-down current
during start-up and shutdown. This function is only avail-
able on the 14-lead PDIP.
V
SW
:
The Switch Output pin is the output of a 1A NPN
totem-pole stage. The V
SW
pin turns the external FET on by
pulling its gate high. Break-Before-Make action of 200ns
on each switch edge is built in to eliminate cross conduc-
tion currents.
I
LIM
:
The I
LIM
pin is the input to the current limit amplifier
and requires the use of a noninductive, power sense
resistor from I
LIM
to ground to set current limit. The typical
current limit threshold voltage is 350mV. The typical input
bias current is 100
μ
A out of the pin.
相關PDF資料
PDF描述
LT1105CN8 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LT1105I RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LT1105IN RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LT1107MJ8-12 Micropower DC/DC Converter Adjustable and Fixed 5V, 12V
LT1107CN8-12 Micropower DC/DC Converter Adjustable and Fixed 5V, 12V
相關代理商/技術參數
參數描述
LT1105CN#PBF 制造商:Linear Technology 功能描述:Conv DC-DC Single 30V 14-Pin PDIP N
LT1105CN8 功能描述:IC OFFLINE SWIT CM HV 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - AC-DC 轉換器，離線開關 系列:- 標準包裝:3,000 系列:- 輸出隔離:隔離 頻率范圍:61kHz ~ 71kHz 輸入電壓:9.4 V ~ 28 V 輸出電壓:12V 功率（瓦特）:- 工作溫度:-40°C ~ 125°C 封裝/外殼:SC-74，SOT-457 供應商設備封裝:6-TSOP 包裝:帶卷 (TR)
LT1105CN8#PBF 制造商:Linear Technology 功能描述:Conv DC-DC Single 30V 8-Pin PDIP N 制造商:Linear Technology 功能描述:IC SWITCHING REG DIP8 1105 制造商:Linear Technology 功能描述:IC, SWITCHING REG, DIP8, 1105 制造商:Linear Technology 功能描述:IC, OFFLINE SWITCHING REGULATOR, DIP-8; Primary Input Voltage:30V; No. of Outputs:1; Output Voltage:50V; Output Current:1.5A; No. of Pins:8; Operating Temperature Min:0C; Operating Temperature Max:70C; MSL:MSL 1 - Unlimited ;RoHS Compliant: Yes
LT1105CS 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Current-Mode SMPS Controller
LT1105I 制造商:LINER 制造商全稱:Linear Technology 功能描述:Offline Switching Regulator
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*