- 您現在的位置：買賣IC網 > PDF目錄377680 > LT1086CT (LINEAR TECHNOLOGY CORP) Hex D-Type Positive-Edge-Triggered Flip-Flops With Clear 16-SOIC 0 to 70 PDF資料下載
參數資料
| 型號： | LT1086CT |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Hex D-Type Positive-Edge-Triggered Flip-Flops With Clear 16-SOIC 0 to 70 |
| 中文描述： | 1.2 V-15 V ADJUSTABLE POSITIVE LDO REGULATOR, 1.5 V DROPOUT, PSFM3 |
| 封裝： | PLASTIC, TO-220, 3 PIN |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 348K |
| 代理商： | LT1086CT |
10
LT1086 Series
APPLICATIO
S I
N
FOR
ATIO
U
Load Regulation
Because the LT1086 is a 3-terminal device, it is not
possible to provide true remote load sensing. Load regu-
lation will be limited by the resistance of the wire connect-
ing the regulator to the load. The data sheet specification
for load regulation is measured at the bottom of the
package. Negative side sensing is a true Kelvin connec-
tion, with the bottom of the output divider returned to the
negative side of the load. Although it may not be immedi-
ately obvious, best load regulation is obtained when the
top of the resistor divider R1 is connected directlyto the
case not to the load This is illustrated in Figure 2. If R1
were connected to the load, the effective resistance be-
tween the regulator and the load would be:
W
U
R
P
, R
P
= Parasitic Line Resistance
R2 + R1
R1
(
)
Thermal Considerations
The LT1086 series of regulators have internal power and
thermal limiting circuitry designed to protect the device
under overload conditions. For continuous normal load
conditions however, maximum junction temperature rat-
ings must not be exceeded. It is important to give careful
consideration to all sources of thermal resistance from
junction to ambient. This includes junction-to-case, case-
to-heat sink interface and heat sink resistance itself. New
thermal resistance specifications have been developed to
more accurately reflect device temperature and ensure
safe operating temperatures. The data section for these
new regulators provides a separate thermal resistance and
maximum junction temperature for both the Control Sec-
tionand the Power Transistor Previous regulators, with a
single junction-to-case thermal resistance specification,
used an average of the two values provided here and
therefore could allow excessive junction temperatures
under certain conditions of ambient temperature and heat
sink resistance. To avoid this possibility, calculations
should be made for both sections to ensure that both
thermal limits are met.
For example, using a LT1086CK (TO-3, Commercial) and
assuming:
V
IN
(max continuous) = 9V, V
OUT
= 5V, I
OUT
= 1A,
T
A
= 75
°
C,
θ
HEAT SINK
= 3
°
C/W,
θ
CASE-TO-HEAT SINK
= 0.2
°
C/W for K package with
thermal compound.
Power dissipation under these conditions is equal to:
P
D
= (V
IN
– V
OUT
)(I
OUT
) = 4W
Junction temperature will be equal to:
T
J
= T
A
+
P
D
(
θ
HEAT SINK
+ θ
CASE-TO-HEAT SINK
+
θ
JC
)
For the Control Section:
T
J
= 75
°
C
+
4W(3
°
C/W
+
0.2
°
C/W
+
0.7
°
C/W) = 95
°
C
95
°
C < 125
°
C = T
JMAX
(Control Section
Commercial Range)
For the Power Transistor:
T
J
= 75
°
C
+
4W(3
°
C/W
+
0.2
°
C/W
+
4
°
C/W) = 103.8
°
C
103.8
°
C < 150
°
C = T
JMAX
(Power Transistor
Commercial Range)
LT1086
OUT
IN
V
IN
ADJ
R
PARASITIC
LINE RESISTANCE
R1*
*CONNECT R1 TO CASE
CONNECT R2 TO LOAD
1086 F02
R
L
R2*
Figure 2. Connections for Best Load Regulation
Connected as shown R
P
is not multiplied by the divider
ratio. R
P
is about 0.004
per foot using 16-gauge wire.
This translates to 4mV/ft at 1A load current, so it is
important to keep the positive lead between regulator and
load as short as possible and use large wire or PC board
traces.
Note that the resistance of the package leads for the H
package
≈
0.06
/inch. While it is usually not possible to
connect the load directly to the package, it is possible to
connect larger wire or PC traces close to the case to avoid
voltage drops that will degrade load regulation.
For fixed voltage devices the top of R1 is internally Kelvin
connected and the ground pin can be used for negative
side sensing.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1086CK-12 | 1.5A Low Dropout Positive Regulators Adjustable and Fixed 2.85V, 3.3V, 3.6V, 5V, 12V |
| LT1086CK-5 | 1.5A Low Dropout Positive Regulators Adjustable and Fixed 2.85V, 3.3V, 3.6V, 5V, 12V |
| LT1086CT-3.3 | 1.5A Low Dropout Positive Regulators Adjustable and Fixed 2.85V, 3.3V, 3.6V, 5V, 12V |
| LT1086CT-3.6 | 1.5A Low Dropout Positive Regulators Adjustable and Fixed 2.85V, 3.3V, 3.6V, 5V, 12V |
| LT1086CT-5 | 1.5A Low Dropout Positive Regulators Adjustable and Fixed 2.85V, 3.3V, 3.6V, 5V, 12V |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1086CT#PBF | 功能描述:IC REG LDO ADJ 1.5A TO220-3 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:8V 輸入電壓:10.5 V ~ 23 V 電壓 - 壓降（標準）:1.7V @ 40mA 穩壓器數量:1 電流 - 輸出:100mA（最小值） 電流 - 限制（最?。?- 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:剪切帶 (CT) 產品目錄頁面:1075 (CN2011-ZH PDF) 其它名稱:296-24390-1 |
| LT1086CT12 | 制造商:Linear Technology 功能描述:IC V REG LDO +12V 1086 TO-220-3 |
| LT1086CT-12 | 功能描述:IC REG LDO 12V 1.5A TO220-3 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 產品培訓模塊:More Information on LDOs 標準包裝:50 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:3.3V 輸入電壓:最高 15V 電壓 - 壓降（標準）:1.1V @ 800mA 穩壓器數量:1 電流 - 輸出:800mA 電流 - 限制（最小）:800mA 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-4，D²Pak（3 引線+接片），TO-263AA 供應商設備封裝:D2PAK-3 包裝:管件 |
| LT1086CT-12#PBF | 功能描述:IC REG LDO 12V 1.5A TO220-3 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:3,000 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:3V 輸入電壓:最高 5.5V 電壓 - 壓降（標準）:0.12V @ 150mA 穩壓器數量:1 電流 - 輸出:150mA（最小值） 電流 - 限制（最小）:220mA 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 供應商設備封裝:TSOT-23-5 包裝:帶卷 (TR) 其它名稱:ADP160AUJZ-3.0-R7TR |
| LT1086CT-12PBF | 制造商:Linear Technology 功能描述:LT1086CT-12PBF |
發布緊急采購，3分鐘左右您將得到回復。