- 您現在的位置：買賣IC網 > PDF目錄377680 > LT1086CK-12 (LINEAR TECHNOLOGY CORP) 1.5A Low Dropout Positive Regulators Adjustable and Fixed 2.85V, 3.3V, 3.6V, 5V, 12V PDF資料下載
參數資料
| 型號： | LT1086CK-12 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 1.5A Low Dropout Positive Regulators Adjustable and Fixed 2.85V, 3.3V, 3.6V, 5V, 12V |
| 中文描述： | 12 V FIXED POSITIVE LDO REGULATOR, 1.5 V DROPOUT, MBFM2 |
| 封裝： | METAL CAN, TO-3, 2 PIN |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 348K |
| 代理商： | LT1086CK-12 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
9
LT1086 Series
plugging and unplugging in the system will not generate
current large enough to do any damage.
The adjustment pin can be driven on a transient basis
±
25V, with respect to the output without any device
degradation. Of course as with any IC regulator, exceeding
the maximum input-to-output voltage differential causes
the internal transistors to break down and none of the
protection circuitry is functional.
the power supply may need to be cycled down to zero and
brought up again to make the output recover.
Ripple Rejection
For the LT1086 the typical curves for ripple rejection
reflect values for a bypassed adjust pin. This curve will be
true for all values of output voltage. For proper bypassing
and ripple rejection approaching the values shown, the
impedance of the adjust pin capacitor at the ripple fre-
quency should equal the value of R1, (normally 100
to
120
). The size of the required adjust pin capacitor is a
function of the input ripple frequency. At 120Hz the adjust
pin capacitor should be 13
μ
F if R1 = 100
. At 10kHz only
0.16
μ
F is needed.
For circuits without an adjust pin bypass capacitor the
ripple rejection will be a function of output voltage. The
output ripple will increase directly as a ratio of the output
voltage to the reference voltage (V
OUT
/V
REF
). For ex-
ample, with the output voltage equal to 5V and no adjust
pin capacitor, the output ripple will be higher by the ratio
of 5V/1.25V or four times larger. Ripple rejection will be
degraded by 12dB from the value shown on the LT1086
curve. Typical curves are provided for the 5V and 12V
devices since the adjust pin is not available.
Output Voltage
The LT1086 develops a 1.25V reference voltage between
the output and the adjust terminal (see Figure 1). By
placing a resistor R1 between these two terminals, a
constant current is caused to flow through R1 and down
through R2 to set the overall output voltage. Normally this
current is chosen to be the specified minimum load
current of 10mA. Because I
ADJ
is very small and constant
when compared with the current through R1, it repre-
sents a small error and can usually be ignored. For fixed
voltage devices R1 and R2 are included in the device.
APPLICATIO
S I
FOR
ATIO
U
W
U
U
V
IN
V
OUT
LT1086
ADJ
IN
OUT
LT1086 AI01
C
ADJ
10
F
C
OUT
150
μ
F
R1
D1
1N4002
(OPTIONAL)
R2
+
+
Overload Recovery
Like any of the IC power regulators, the LT1086 has safe
area protection. The safe area protection decreases the
current limit as input-to-output voltage increases and
keeps the power transistor inside a safe operating region
for all values of input-to-output voltage. The LT1086
protection is designed to provide some output current at
all values of input-to-output voltage up to the device
breakdown.
When power is first turned on, as the input voltage rises,
the output follows the input, allowing the regulator to start
up into very heavy loads. During the start-up, as the input
voltage is rising, the input-to-output voltage differential
remains small, allowing the regulator to supply large
output currents. With high input voltage, a problem can
occur wherein removal of an output short will not allow the
output voltage to recover. Older regulators such as the
7800 series also exhibited this phenomenon, so it is not
unique to the LT1086.
The problem occurs with a heavy output load when the
input voltage is high and the output voltage is low, such as
immediately after a removal of a short. The load line for
such a load may intersect the output current curve at two
points. If this happens there are two stable output operat-
ing points for the regulator. With this double intersection
Figure 1. Basic Adjustable Regulator
R1
10
μ
F
TANTALUM
R2
IN
OUT
I
ADJ
50
A
ADJ
V
OUT
LT1086
V
IN
1086 F01
V
REF
V
OUT
= V
REF
1 + R1
ADJ
R2
(
)
+
相關PDF資料 |
PDF描述 |
|---|---|
| LT1086CK-5 | 1.5A Low Dropout Positive Regulators Adjustable and Fixed 2.85V, 3.3V, 3.6V, 5V, 12V |
| LT1086CT-3.3 | 1.5A Low Dropout Positive Regulators Adjustable and Fixed 2.85V, 3.3V, 3.6V, 5V, 12V |
| LT1086CT-3.6 | 1.5A Low Dropout Positive Regulators Adjustable and Fixed 2.85V, 3.3V, 3.6V, 5V, 12V |
| LT1086CT-5 | 1.5A Low Dropout Positive Regulators Adjustable and Fixed 2.85V, 3.3V, 3.6V, 5V, 12V |
| LT1086IM-3.3 | 1.5A Low Dropout Positive Regulators Adjustable and Fixed 2.85V, 3.3V, 3.6V, 5V, 12V |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1086CK-5 | 制造商:Linear Technology 功能描述:LDO Regulator Pos 5V 1.5A 3-Pin(2+Tab) TO-3 |
| LT1086CM | 功能描述:IC REG LDO ADJ 1.5A 3DD RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:800 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:2.5V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.7V @ 4A 穩壓器數量:1 電流 - 輸出:4A 電流 - 限制（最小）:4.2A 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6，D²Pak（5 引線+接片），TO-263BA 供應商設備封裝:TO-263-5 包裝:帶卷 (TR) 其它名稱:AP1184K525L-13AP1184K525LDITR |
| LT1086CM#PBF | 功能描述:IC REG LDO ADJ 1.5A 3DD RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:8V 輸入電壓:10.5 V ~ 23 V 電壓 - 壓降（標準）:1.7V @ 40mA 穩壓器數量:1 電流 - 輸出:100mA（最小值） 電流 - 限制（最?。?- 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:剪切帶 (CT) 產品目錄頁面:1075 (CN2011-ZH PDF) 其它名稱:296-24390-1 |
| LT1086CM#TR | 功能描述:IC REG LDO ADJ 1.5A 3DD RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:800 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:2.5V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.7V @ 4A 穩壓器數量:1 電流 - 輸出:4A 電流 - 限制（最小）:4.2A 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6，D²Pak（5 引線+接片），TO-263BA 供應商設備封裝:TO-263-5 包裝:帶卷 (TR) 其它名稱:AP1184K525L-13AP1184K525LDITR |
| LT1086CM#TRPBF | 功能描述:IC REG LDO ADJ 1.5A 3DD RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:800 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:2.5V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.7V @ 4A 穩壓器數量:1 電流 - 輸出:4A 電流 - 限制（最?。?4.2A 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6，D²Pak（5 引線+接片），TO-263BA 供應商設備封裝:TO-263-5 包裝:帶卷 (TR) 其它名稱:AP1184K525L-13AP1184K525LDITR |
發布緊急采購，3分鐘左右您將得到回復。