- 您現在的位置：買賣IC網 > PDF目錄30765 > LT1054IN8#TRPBF (LINEAR TECHNOLOGY CORP) SWITCHED CAPACITOR REGULATOR, 40 kHz SWITCHING FREQ-MAX, PDIP8 PDF資料下載
參數資料
| 型號： | LT1054IN8#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHED CAPACITOR REGULATOR, 40 kHz SWITCHING FREQ-MAX, PDIP8 |
| 封裝： | 0.300 INCH, LEAD FRE, PLASTIC, DIP-8 |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 264K |
| 代理商： | LT1054IN8#TRPBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁
LT1054/LT1054L
6
1054lfg
transistor must be added as shown in Figure 1. This will
prevent VOUT (Pin 5) from being pulled above the ground
pin (Pin 3) during start-up. Any small, general purpose
transistor such as 2N2222 or 2N2219 can be used. RX
should be chosen to provide enough base drive to the
external transistor so that it is saturated under nominal
output voltage and maximum output current conditions.
In some cases an N-channel enhancement mode MOSFET
can be used in place of the transistor.
RX ≤
VOUT
(
)β
IOUT
OSC (Pin 7): Oscillator Pin. This pin can be used to raise
or lower the oscillator frequency or to synchronize the
device to an external clock. Internally Pin 7 is connected
to the oscillator timing capacitor (Ct ≈ 150pF) which is
alternately charged and discharged by current sources of
±7A so that the duty cycle is ≈50%. The LT1054 oscillator
is designed to run in the frequency band where switch-
ing losses are minimized. However the frequency can be
raised, lowered, or synchronized to an external system
clock if necessary.
The frequency can be lowered by adding an external
capacitor (C1, Figure 2) from Pin 7 to ground. This will
increase the charge and discharge times which lowers the
oscillator frequency. The frequency can be increased by
adding an external capacitor (C2, Figure 2, in the range
of 5pF to 20pF) from Pin 2 to Pin 7. This capacitor will
couple charge into CT at the switch transitions, which will
shorten the charge and discharge time, raising the oscil-
lator frequency. Synchronization can be accomplished
by adding an external resistive pull-up from Pin 7 to the
reference pin (Pin 6). A 20k pull-up is recommended. An
open collector gate or an NPN transistor can then be used
to drive the oscillator pin at the external clock frequency
as shown in Figure 2. Pulling up Pin 7 to an external volt-
age is not recommended. For circuits that require both
frequency synchronization and regulation, an external
reference can be used as the reference point for the top
of the R1/R2 divider allowing Pin 6 to be used as a pull-
up point for Pin 7.
–
+
LOAD
CIN
COUT
LT1054 F01
IL
V+
RX
LT1054
FB/SHDN
CAP+
GND
CAP–
V+
OSC
VREF
VOUT
IQ
IOUT
+
VREF (Pin 6): Reference Output. This pin provides a 2.5V
reference point for use in LT1054-based regulator circuits.
The temperature coefficient of the reference voltage has
been adjusted so that the temperature coefficient of the
regulated output voltage is close to zero. This requires the
reference output to have a positive temperature coefficient
as can be seen in the typical performance curves. This
nonzero drift is necessary to offset a drift term inherent
in the internal reference divider and comparator network
tied to the feedback pin. The overall result of these drift
terms is a regulated output which has a slight positive
temperature coefficient at output voltages below 5V and a
slight negative TC at output voltages above 5V. Reference
output current should be limited, for regulator feedback
networks, to approximately 60A. The reference pin will
draw ≈100A when shorted to ground and will not af-
fect the internal reference/regulator, so that this pin can
also be used as a pull-up for LT1054 circuits that require
synchronization.
Figure 1
Figure 2
VIN
COUT
CIN
C2
C1
LT1054 F02
LT1054
FB/SHDN
CAP+
GND
CAP–
V+
OSC
VREF
VOUT
+
V+ (Pin 8): Input Supply. The LT1054 alternately charges
CIN to the input voltage when CIN is switched in parallel
with the input supply and then transfers charge to COUT
when CIN is switched in parallel with COUT. Switching oc-
curs at the oscillator frequency. During the time that CIN
PIN FUNCTIONS
相關PDF資料 |
PDF描述 |
|---|---|
| LT1054MJ8#TRPBF | SWITCHED CAPACITOR REGULATOR, 40 kHz SWITCHING FREQ-MAX, CDIP8 |
| LT1076HVCT#TRPBF | 3.2 A SWITCHING REGULATOR, 125 kHz SWITCHING FREQ-MAX, PZFM7 |
| LT1076IT-5#TR | 3.2 A SWITCHING REGULATOR, 120 kHz SWITCHING FREQ-MAX, PZFM5 |
| LT1076HVIT-5#TRPBF | 3.2 A SWITCHING REGULATOR, 120 kHz SWITCHING FREQ-MAX, PZFM5 |
| LT1076HVCT-5#TR | 3.2 A SWITCHING REGULATOR, 120 kHz SWITCHING FREQ-MAX, PZFM5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1054IP | 功能描述:電荷泵 Switched-Capacitor Voltage Converter RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
| LT1054IP | 制造商:Texas Instruments 功能描述:Voltage Regulator IC Package/Case:8-PDIP |
| LT1054IPE4 | 功能描述:電荷泵 Switched-Capacitor Voltage Converter RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
| LT1054IS8 | 功能描述:IC REG SWITCHD CAP DBL INV 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT1054IS8#PBF | 功能描述:IC REG SWITCHD CAP DBL INV 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
發布緊急采購，3分鐘左右您將得到回復。