- 您現在的位置：買賣IC網 > PDF目錄358951 > LT1014MJ (LINEAR TECHNOLOGY CORP) SMD 0.1 UF CERAM PDF資料下載
參數資料
| 型號： | LT1014MJ |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | SMD 0.1 UF CERAM |
| 中文描述： | QUAD OP-AMP, 300 uV OFFSET-MAX, CDIP14 |
| 封裝： | 0.300 INCH, HERMETIC SEALED, CERAMIC, DIP-14 |
| 文件頁數： | 19/30頁 |
| 文件大?。?/td> | 631K |
| 代理商： | LT1014MJ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039C – JULY 1989 – REVISED SEPTEMBER 1999
19
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
comparator applications
The single-supply operation of the LT1014 can be used as a precision comparator with TTL-compatible output.
In systems using both operational amplifiers and comparators, the LT1014 can perform multiple duties (see
Figures 25 and 26).
Figure 25. Low-to-High-Level Output Response
for Various Input Overdrives
100 mV
10 mV
5 mV
2 mV
D
I
t – Time –
μ
s
Overdrive
VCC+ = 5 V
VCC– = 0
TA = 25
°
C
–
V
O
5
4
3
2
1
0
0
50
100 150 200 250 300 350 400 450
Figure 26. High-to-Low-Level Output Response
for Various Input Overdrives
2 mV
5 mV
100 mV
Overdrive
10 mV
D
I
t – Time –
μ
s
VCC+ = 5 V
VCC– = 0
TA = 25
°
C
–
V
O
5
4
3
2
1
0
0
50
100 150 200 250 300 350 400 450
low-supply operation
The minimum supply voltage for proper operation of the LT1014 is 3.4 V (three Ni-Cad batteries). Typical supply
current at this voltage is 290
μ
A; therefore, power dissipation is only 1 mW per amplifier.
offset voltage and noise testing
Figure 30 shows the test circuit for measuring input offset voltage and its temperature coefficient. This circuit
with supply voltages increased to
±
20 V is also used as the burn-in configuration.
The peak-to-peak equivalent input noise voltage of the LT1014 is measured using the test circuit shown in
Figure 27. The frequency response of the noise tester indicates that the 0.1-Hz corner is defined by only one
zero. The test time to measure 0.1-Hz to 10-Hz noise should not exceed 10 seconds, as this time limit acts as
an additional zero to eliminate noise contribution from the frequency band below 0.1 Hz.
An input noise-voltage test is recommended when measuring the noise of a large number of units. A 10-Hz input
noise-voltage measurement correlates well with a 0.1-Hz peak-to-peak noise reading because both results are
determined by the white noise and the location of the 1/f corner frequency.
Noise current is measured by the circuit and formula shown in Figure 28. The noise of the source resistors is
subtracted.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1014IS | SMD-CAP,CER,.001UF,5% 100V,X7R,.08X.05 |
| LT1014IN | CAP: CERAMIC CHIP, 2.2UF, +/- 10% (OR BETTER), 10V |
| LT1014DS | 10 UF,16V,20%,0805,ROHS |
| LT1014DN | Quad Precision Op Amp |
| LT1014 | Quad Precision Op Amp |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1014MJ/883 | 制造商:Linear Technology 功能描述:OP Amp Quad GP ±22V/44V 14-Pin CDIP |
| LT1014MJ/883C | 制造商:Linear Technology 功能描述: |
| LT1014MJB | 制造商:Texas Instruments 功能描述:OP Amp Quad GP ±22V/44V 14-Pin CDIP Tube 制造商:Texas Instruments 功能描述:OP Amp Quad GP 22V/44V 14-Pin CDIP Tube |
| LT1014MN | 制造商:TI 制造商全稱:Texas Instruments 功能描述:QUAD PRECISION OPERATIONAL AMPLIFIERS |
| LT1014N | 制造商:TI 制造商全稱:Texas Instruments 功能描述:QUAD PRECISION OPERATIONAL AMPLIFIERS |
發布緊急采購，3分鐘左右您將得到回復。