- 您現在的位置：買賣IC網 > PDF目錄358951 > LT1013AMJ8 (LINEAR TECHNOLOGY CORP) Quad Precision Op Amp PDF資料下載
參數資料
| 型號： | LT1013AMJ8 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | Quad Precision Op Amp |
| 中文描述： | DUAL OP-AMP, 300 uV OFFSET-MAX, CDIP8 |
| 封裝： | 0.300 INCH, HERMETIC SEALED, CERAMIC, DIP-8 |
| 文件頁數： | 20/25頁 |
| 文件大小： | 420K |
| 代理商： | LT1013AMJ8 |
LT1013, LT1013A, LT1013D, LT1013Y
DUAL PRECISION OPERATIONAL AMPLIFIERS
SLOS018B – MAY 1988 – REVISED OCTOBER 1996
20
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
comparator applications
The single-supply operation of the LT1013 lends itself for use as a precision comparator with TTL-compatible
output. In systems using both operational amplifiers and comparators, the LT1013 can perform multiple duties.
Refer to Figures 25 and 26.
VO
100 mV
VCC+ = 5 V
VCC– = 0
TA = 25
°
C
Overdrive
10 mV
5 mV
2 mV
0
50 100 150 200 250 300 350 400 450
t – Time –
μ
s
5
4
3
2
1
0
D
I
Figure 25. Low-to-High-Level Output
Response for Various Input Overdrives
V
2 mV
5 mV
Overdrive
10 mV
0
50 100 150 200 250 300 350 400 450
t – Time –
μ
s
5
4
3
2
1
0
D
I
VCC+ = 5 V
VCC– = 0
TA = 25
°
C
100 mV
Figure 26. High-to-Low-Level Output
Response for Various Input Overdrives
low-supply operation
The minimum supply voltage for proper operation of the LT1013 is 3.4 V (three Ni-Cad batteries). Typical supply
current at this voltage is 290
μ
A; therefore, power dissipation is only 1 mW per amplifier.
offset voltage and noise testing
The test circuit for measuring input offset voltage and its temperature coefficient is shown in Figure 30. This
circuit with supply voltages increased to
±
20 V is also used as the burn-in configuration.
The peak-to-peak equivalent input noise voltage of the LT1013 is measured using the test circuit shown in
Figure 27. The frequency response of the noise tester indicates that the 0.1-Hz corner is defined by only one
zero. The test time to measure 0.1-Hz to 10-Hz noise should not exceed 10 seconds, as this time limit acts as
an additional zero to eliminate noise contribution from the frequency band below 0.1 Hz.
An input noise voltage test is recommended when measuring the noise of a large number of units. A 10-Hz input
noise voltage measurement correlates well with a 0.1-Hz peak-to-peak noise reading because both results are
determined by the white noise and the location of the 1/f corner frequency.
Current noise is measured by the circuit and formula shown in Figure 28. The noise of the source resistors is
subtracted.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1013CH | Quad Precision Op Amp |
| LT1013CN8 | Quad Precision Op Amp |
| LT1013DN8 | Quad Precision Op Amp |
| LT1013DS8 | Quad Precision Op Amp |
| LT1013MH | Quad Precision Op Amp |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1013AMJ8/883 | 制造商:Linear Technology 功能描述:OP Amp Dual GP ±22V/44V 8-Pin CDIP |
| LT1013AMJG | 制造商:Texas Instruments 功能描述:OP Amp Dual GP 制造商:Rochester Electronics LLC 功能描述:DUAL PRECISION OP AMP - Bulk 制造商:Texas Instruments 功能描述:OP AMP DUAL GP 22V/44V 8CDIP - Rail/Tube 制造商:Texas Instruments 功能描述:DUAL PRECISION OP AMP 制造商:Texas Instruments 功能描述:IC OP AMP DUAL PRECISION CDIP8 制造商:Texas Instruments 功能描述:IC, OP AMP, DUAL PRECISION, CDIP8 制造商:Texas Instruments 功能描述:OP Amp Dual General Purpose 22/44V |
| LT1013AMJGB | 制造商:Texas Instruments 功能描述:OP Amp Dual GP 制造商:Texas Instruments 功能描述:IC OP AMP DUAL PRECISION CDIP8 |
| LT1013AML | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier |
| LT1013AMP | 制造商:TI 制造商全稱:Texas Instruments 功能描述:DUAL PRECISION OPERATIONAL AMPLIFIERS |
發布緊急采購，3分鐘左右您將得到回復。