參數資料
| 型號： | LT1007IS8#TR |
| 廠商： | Linear Technology |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OP AMP PREC SGL HI SPD 8SOIC |
| 標準包裝： | 2,500 |
| 放大器類型： | 通用 |
| 電路數： | 1 |
| 轉換速率： | 2.5 V/µs |
| 增益帶寬積： | 8MHz |
| 電流 - 輸入偏壓： | 15nA |
| 電壓 - 輸入偏移： | 20µV |
| 電壓 - 電源，單路/雙路(±)： | ±4 V ~ 18 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 帶卷 (TR) |
10
LT1007/LT1037
sn100737 100737fbs
APPLICATIONS INFORMATION
WU
U
As with all operational amplifiers when RF > 2k, a pole will
be created with RF and the amplifier’s input capacitance,
creating additional phase shift and reducing the phase
margin. A small capacitor (20pF to 50pF) in parallel with RF
will eliminate this problem.
Noise Testing
The 0.1Hz to 10Hz peak-to-peak noise of the LT1007/
LT1037 is measured in the test circuit shown (Figure 5a).
The frequency response of this noise tester (Figure 5b)
indicates that the 0.1Hz corner is defined by only one zero.
The test time to measure 0.1Hz to 10Hz noise should not
exceed ten seconds, as this time limit acts as an additional
zero to eliminate noise contributions from the frequency
band below 0.1Hz.
Measuring the typical 60nV peak-to-peak noise perfor-
mance of the LT1007/LT1037 requires special test
precautions:
1. The device should be warmed up for at least five
minutes. As the op amp warms up, its offset voltage
changes typically 3
V due to its chip temperature
increasing 10
°C to 20°C from the moment the power
supplies are turned on. In the ten-second measurement
interval these temperature-induced effects can easily
exceed tens of nanovolts.
2. For similar reasons, the device must be well shielded
from air currents to eliminate the possibility of thermo-
electric effects in excess of a few nanovolts, which
would invalidate the measurements.
3. Sudden motion in the vicinity of the device can also
“feedthrough” to increase the observed noise.
A noise voltage density test is recommended when mea-
suring noise on a large number of units. A 10Hz noise
voltage density measurement will correlate well with a
0.1Hz to 10Hz peak-to-peak noise reading since both
results are determined by the white noise and the location
of the 1/f corner frequency.
Current noise is measured in the circuit shown in Figure 6
and calculated by the following formula:
i
e
nV
M
n
no
=
() ()
()( )
2
12
130
101
1
101
/
FREQUENCY (Hz)
100
90
80
70
60
50
40
30
0.01
1
10
100
1007/37F05b
0.1
GAIN
(dB)
1007/37 F05a
10
0.1
F
4.7
F
VOLTAGE GAIN
= 50,000
24.3k
100k
–
+
–
+
*
LT1007
LT1037
LT1001
2k
4.3k
110k
100k
SCOPE
× 1
RIN = 1M
*DEVICE UNDER TEST
NOTE: ALL CAPACITOR VALUES ARE FOR
NONPOLARIZED CAPACITORS ONLY
2.2
F
0.1
F
22
F
Figure 5a. 0.1Hz to 10Hz Noise Test Circuit
1007/37 F06
100
100k
–
+
LT1007
LT1037
500k
eno
Figure 6
Figure 5b. 0.1Hz to 10Hz Peak-to-
Peak Noise Tester Frequency
Response
相關PDF資料 |
PDF描述 |
|---|---|
| 70280-0452 | CONN HDR DUAL 88POS .100 SRT AU |
| CLT-133-01-L-D | CONN RCPT 66POS DUAL 2MM T/H |
| 10-89-7722 | CONN HDR DUAL 72POS .100 SRT AU |
| RL1206FR-070R33L | RES 0.33 OHM 1/4W 1% 1206 SMD |
| 929665-09-09-I | CONN HEADER .100 DUAL STR 18POS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1007MH | 制造商:Linear Technology 功能描述:OP Amp Single GP ±22V 8-Pin TO-5 |
| LT1007MH/883 | 制造商:Linear Technology 功能描述:OP Amp Single GP ±22V 8-Pin TO-5 制造商:Linear Technology 功能描述:OP Amp Single GP ??22V 8-Pin TO-5 |
| LT1007MJ8 | 制造商:Linear Technology 功能描述:OP Amp Single GP ±22V 8-Pin CDIP 制造商:Linear Technology 功能描述:OP Amp Single GP ??22V 8-Pin CDIP |
| LT1007MJG | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW-NOISE, HIGH-SPEED, PRECISION OPERATIONAL AMPLIFIERS |
| LT1007ML | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier |
發(fā)布緊急采購，3分鐘左右您將得到回復。