- 您現在的位置：買賣IC網 > PDF目錄95793 > LSP3128SAD (LITE-ON SEMICONDUCTOR CORP) SWITCHING REGULATOR, PDSO8 PDF資料下載
參數資料
| 型號： | LSP3128SAD |
| 廠商： | LITE-ON SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, PDSO8 |
| 封裝： | SOP-8 |
| 文件頁數： | 4/10頁 |
| 文件大?。?/td> | 342K |
| 代理商： | LSP3128SAD |
Liteon Semiconductor Corporation
LSP3128
Wide Input 3A Step Down Converter
Rev1.0
3/10
FUNCTIONAL BLOCK DIAGRAM
FUNCTIONAL DESCROPTION
As seen in the Functional Block Diagram, the LSP3128 is a current mode pulse width modulation (PWM) converter.
The converter operates as follows :
A switching cycle starts when the rising edge of the Oscillator clock output causes the High-Side Power Switch to
turn on and the Low-Side Power Switch to turn off. With the SW side of the inductor now connected to IN, the
inductor current ramps up to store energy in its magnetic field. The inductor current level is measured by the Current
Sense Amplifier and added to the Oscillator ramp signal. If the resulting summation is higher than the COMP voltage,
the output of the PWM Comparator goes high. When this happens or when Oscillator clock output goes low, the
High-Side Power Switch turns off and the Low-Side Power Switch turns on. At this point, the SW side of the inductor
swings to a diode voltage below ground, causing the inductor current to decrease and magnetic energy to be
transferred to the output. This state continues until the cycle starts again.
The High-Side Power Switch is driven by logic using the BS bootstrap pin as the positive rail. This pin is charged to
VSW + 6V when the Low-Side Power Switch turns on.
The COMP voltage is the integration of the error between the FB input and the internal 1.222V reference. If FB is
lower than the reference voltage, COMP tends to go higher to increase current to the output. Current limit happens
when COMP reaches its maximum clamp value of 2.65V.
The Oscillator normally switches at 400kHz. However, if the FB voltage is less than 0.7V, then the switching
frequency decreases until it reaches a typical value of 40kHz at VFB = 0V.
Shutdown Control
The LSP3128 has an enable input EN for turning the IC on or off. When EN is less than 0.7V, the IC is in 6A low
current shutdown mode and the output is discharged through the Low-Side Power Switch. When EN is higher than
1.3V, the IC is in normal operation mode. EN is internally pulled up with a 2A current source and can be left
unconnected for always-on operation.
Thermal Shutdown
The LSP3128 automatically turns off when its junction temperature exceeds 160°C and then restarts once the
temperature falls to 150°C.
相關PDF資料 |
PDF描述 |
|---|---|
| LSP3603TCAK | SWITCHING REGULATOR, PDSO6 |
| LST0400-ST-F | FIBER OPTIC LED EMITTER, 1285-1345nm, THROUGH HOLE MOUNT, ST CONNECTOR |
| LST0400-FC-A | FIBER OPTIC LED EMITTER, 1285-1345nm, PANEL MOUNT, FC CONNECTOR |
| LST0500-ST-F | FIBER OPTIC LED EMITTER, 1285-1345nm, PANEL MOUNT, ST CONNECTOR |
| LST0400-FC-A | FIBER OPTIC LED EMITTER, 1285-1345nm, PANEL MOUNT, FC CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LSP32-K2-RGBA | 制造商:Dialight 功能描述:LED MODULE 32X K2 RGBA |
| LSP-32K2-RGBW | 制造商:Dialight 功能描述: |
| LSP32-K2-RGBW | 制造商:Dialight 功能描述:LED MODULE 32X K2 RGBW |
| LSP-32K2-WWWW | 制造商:Dialight 功能描述: |
| LSP32-K2-WWWW | 制造商:Dialight 功能描述:LED MODULE 32X K2 WWWW |
發布緊急采購，3分鐘左右您將得到回復。