- 您現在的位置：買賣IC網 > PDF目錄377665 > lS80C86 (Intersil Corporation) CMOS 16-Bit Microprocessor PDF資料下載
參數資料
| 型號： | lS80C86 |
| 廠商： | Intersil Corporation |
| 元件分類： | 16位微控制器 |
| 英文描述： | CMOS 16-Bit Microprocessor |
| 中文描述： | 的CMOS 16位微處理器 |
| 文件頁數： | 6/35頁 |
| 文件大?。?/td> | 339K |
| 代理商： | LS80C86 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
3-146
DT/R
27
O
DATA TRANSMIT/RECEIVE: is needed in a minimum system that desires to use a data bus
transceiver. It is used to control the direction of data flow through the transceiver. Logically,
DT/R is equivalent to S1 in maximum mode, and its timing is the same as for M/IO (T = HIGH,
R = LOW). DT/R is held to a high impedance logic one during local bus “hold acknowledge”.
DEN
26
O
DATA ENABLE: provided as an output enable for a bus transceiver in a minimum system which
uses the transceiver. DEN is active LOW during each memory and I/O access and for INTA cy-
cles. For a read or INTA cycle it is active from the middle of T2 until the middle of T4, while for a
write cycle it is active from the beginning of T2 until the middle of T4. DEN is held to a high im-
pedance logic one during local bus “hold acknowledge”.
HOLD
HLDA
31, 30
I
O
HOLD: indicates that another master is requesting a local bus “hold”. To be an acknowledged,
HOLD must be active HIGH. The processor receiving the “hold” will issue a “hold acknowledge”
(HLDA) in the middle of a T4 or TI clock cycle. Simultaneously with the issuance of HLDA, the
processor will float the local bus and control lines. After HOLD is detected as being LOW, the
processor will lower HLDA, and when the processor needs to run another cycle, it will again drive
the local bus and control lines.
HOLD is not an asynchronous input. External synchronization should be provided if the system
cannot otherwise guarantee the setup time.
Maximum Mode System
The following pin function descriptions are for the 80C86 system in maximum mode (i.e., MN/MX - GND). Only the pin functions which are
unique to maximum mode are described below.
SYMBOL
PIN
NUMBER
TYPE
DESCRIPTION
S0
S1
S2
26
27
28
O
O
O
STATUS: is active during T4, T1 and T2 and is returned to the passive state (1, 1, 1) during T3
or during TW when READY is HIGH. This status is used by the 82C88 Bus Controller to generate
all memory and I/O access control signals. Any change by S2, S1 or S0 during T4 is used to
indicate the beginning of a bus cycle, and the return to the passive state in T3 or TW is used to
indicate the end of a bus cycle.
These signals are held at a high impedance logic one state during “grant sequence”.
Minimum Mode System
(Continued)
The following pin function descriptions are for the 80C86 in minimum mode (i.e., MN/MX = V
CC
). Only the pin functions which are unique to
minimum mode are described; all other pin functions are as described below.
SYMBOL
PIN
NUMBER
TYPE
DESCRIPTION
S2
S1
S0
CHARACTERISTICS
0
0
0
Interrupt Acknowledge
0
0
1
Read I/O Port
0
1
0
Write I/O Port
0
1
1
Halt
1
0
0
Code Access
1
0
1
Read Memory
1
1
0
Write Memory
1
1
1
Passive
80C86
相關PDF資料 |
PDF描述 |
|---|---|
| lS80C88 | CMOS 8/16-Bit Microprocessor |
| LS830 | ULTRA LOW LEAKAGE LOW DRIFT MONOLITHIC DUAL N-CHANNEL JFET |
| LS830-3 | ULTRA LOW LEAKAGE LOW DRIFT MONOLITHIC DUAL N-CHANNEL JFET |
| LS831 | ULTRA LOW LEAKAGE LOW DRIFT MONOLITHIC DUAL N-CHANNEL JFET |
| LS832 | ULTRA LOW LEAKAGE LOW DRIFT MONOLITHIC DUAL N-CHANNEL JFET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LS80C88 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 8/16-Bit Microprocessor |
| LS-8101F | 制造商:OSEPP 功能描述:SERVO - METAL GEAR DIGITAL SERVO - 360 |
| LS8107M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| LS8141AM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| LS8141CM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。