參數資料
型號: LS7634
廠商: LSI Corporation
英文描述: TOUCH CONTROL HALOGEN LAMP DIMMER
中文描述: 觸摸式控制鹵素?zé)粽{(diào)光器
文件頁數: 2/4頁
文件大?。?/td> 74K
代理商: LS7634
The differences among all versions of LS7634 and LS7635 are:
LS7634 (LS7634FO)
Upon power-up, the TRIG output is Off.
(Upon power-up, the TRIG output is On at maximum conduction angle.)
When a LONG touch is applied, the dimming direction automatically re-
verses whenever maximum or minimum conduction angles are reached.
LS7635 (LS7635FO)
Upon power-up, the TRIG output is Off.
(Upon power-up, the TRIG output is On at maximum conduction angle.)
When a LONG touch is applied, the dimming stops whenever maximum
or minimum conduction angles are reached. In order to change dimming
levels from maximum or minimum, LONG touch must be removed and
reapplied.The purpose of this feature is to allow the user to positively
locate maximum and minimum conduction angles.
TABLE 1
MODE SHORT TOUCH LONG TOUCH DIMMING
REVERSAL
PRE-TOUCH POST-TOUCH PRE-TOUCH POST-TOUCH
OFF
MAX(Note 1)
OFF/MIN
0
ON
OFF
MAX
INTERMEDIATE
(Note 5)
Varies up from MIN
Varies down from MAX
Varies from INTERMEDIATE
N/A
N/A
NO
OFF
MEMORY
(Notes 2, 3)
OFF
OFF
MIN
MAX
INTERMEDIATE
Varies from memory (Notes 2, 3,4)
Varies up from MIN
Varies down from MAX
Varies from INTERMEDIATE
YES
N/A
N/A
YES
1
ON
OFF
2
ON
MAX (Note 1)
OFF
OFF/MIN
MAX
INTERMEDIATE
Varies up from MIN
Varies down from MAX
Varies from INTERMEDIATE
N/A
N/A
YES
Note 1
:
Note 2
: A soft turn-on is produced by slewing up , from minimum to memory.
Upon power-up the memory value is defaulted to maximum conduction angle.
Note 3
:
“Memory” refers to the conduction angle, , which existed prior to the current off-state.
Note 4
: A soft turn-on is produced by slewing up from minimum to memory upon which the dimming is started.
Note 5: NO
= Dimming direction does not reverse from prior dimming direction.
YES
= Dimming direction does reverse from prior dimming direction.
N/A
= Does not apply.
A soft turn-on is produced by slewing up the conduction angle, , from minimum at the rate of 1.4
/8.33ms (60Hz).
7634/7635-010906-2
LS7635 NOTE
:
If the User applies a LONG Touch when the TRIG Conduc-
tion Angle is within a “few” degrees of Maximum or Mini-
mum, the TRIG Conduction Angle can move to Maximum or
Minimum and stop without the User being able to observe a
change in brightness. There-fore, the User should be in-
structed that if no change in brightness is observed in re-
sponse to a LONG Touch, the LONG Touch should be re
moved and reapplied in order to produce a change in bright-
ness.
ABSOLUTE MAXIMUM RATINGS:
PARAMETER SYMBOL VALUE
DC supply voltage V
DD
- Vss +7
Any input voltage
Operating temperature
Storage temperature
UNIT
V
V
°C
°C
V
IN
T
A
T
STG
Vss - 0.3 to V
DD
+ 0.3
0 to +90
-65 to +150
DC ELECTRICAL CHARACTERISTICS:
(T
A
= +25C, all voltages referenced to Vss. V
DD
= +5V unless otherwise noted.)
PARAMETER
SYMBOL
MIN
TYP
MAX
UNIT
CONDITION
Supply voltage
Supply current
V
DD
I
DD
4.5
-
5.0
300
5.5
400
V
-
μA
Output unloaded
V
DD
= 5.5V
-
SYNC
Lo
V
ISL
-
-
2.1
V
SYNC
Hi
V
ISH
2.9
-
-
V
-
EXT, SENS
Lo
V
IEL
-
-
1.5
V
-
EXT, SENS
H
i
TRIG Lo
TRIG H
i
V
IEH
V
OL
V
OH
3.5
-
-
-
-
-
-
V
V
V
-
-
-
0.2
5.0
TRIG
Sink Current
I
TSNK
35
-
- mA
V
OTRIG
= 2.5V
相關PDF資料
PDF描述
LS7634FO TOUCH CONTROL HALOGEN LAMP DIMMER
LS7635 TOUCH CONTROL HALOGEN LAMP DIMMER
LS7635FO TOUCH CONTROL HALOGEN LAMP DIMMER
LS80C32 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
LS80C52 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
相關代理商/技術參數
參數描述
LS7634FO 制造商:LSI 制造商全稱:LSI 功能描述:TOUCH CONTROL HALOGEN LAMP DIMMER
LS7635 制造商:LSI 制造商全稱:LSI 功能描述:TOUCH CONTROL HALOGEN LAMP DIMMER
LS7635FO 制造商:LSI 制造商全稱:LSI 功能描述:TOUCH CONTROL HALOGEN LAMP DIMMER
LS7636 制造商:LSI 制造商全稱:LSI 功能描述:REVERSE PHASE (TRAILING-EDGE) HALOGEN LAMP DIMMER
LS7636FO 制造商:LSI 制造商全稱:LSI 功能描述:REVERSE PHASE (TRAILING-EDGE) HALOGEN LAMP DIMMER