- 您現在的位置：買賣IC網 > PDF目錄369838 > LS7560-S Controller Miscellaneous - Datasheet Reference PDF資料下載
參數資料
| 型號： | LS7560-S |
| 英文描述： | Controller Miscellaneous - Datasheet Reference |
| 中文描述： | 控制器雜項-數據表參考 |
| 文件頁數： | 2/8頁 |
| 文件大?。?/td> | 86K |
| 代理商： | LS7560-S |
ERROR AMPLIFIER Inputs
(Pins 6, 7 )
Output
(Pin 8)
For closed loop control, the TACHOMETER Output is applied
through a resistor to the negative input of the Error Amplifier on
Pin 7. A speed control potentiometer is connected to the positive
input of the Error Amplifier on Pin 6. A parallel RC Network is con-
nected between the Output of the Error Amplifier on Pin 8 and Pin
7. The Amplifier, configured this way, enables the variable pulse
width to be converted to a DC voltage which is used to control the
motor speed. The potentiometer is used to set the desired motor
speed. For open loop control, configure the Error Amplifier as a
voltage follower by connecting Pin 7 directly to Pin 8 and do not
connect the TACHOMETER Output signal to the Error Amplifier.
TOP DRIVER POLARITY SELECT Input
(Pin 20)
A High on this input selects a High Polarity for the Top Output
Drivers Motor ON condition and a Low selects a Low Polarity.
OUTPUT DRIVERS
(Pins 12, 13, 14, 15, 16, 17)
Each Driver Output provides a CMOS compatible signal for driv-
ing Buffers/Power Transistors. The Outputs are capable of sink-
ing/sourcing 25mA with a 1.5V drop across the IC, at V
DD
= 12V.
FAULT INDICATOR Output
(Pin 3)
Open drain output to provide sinking current for driving an ex-
ternal device such as an LED to indicate a malfunction condition.
The output occurs under any of the following conditions:
1) Overcurrent Sense condition
2) ENABLE Input below V
R
/2.2
3) Invalid Sensor code
4) Chip power supply less than 9V
5) V
R
Output less than 4.1V
V
R
Output
(Pin 19)
5.5V Reference Voltage Output that can supply 20mA of current
at V
DD
=12V for powering input Sensors.
V
DD
(Pin 28)
V
DD
is Supply Voltage positive terminal.
OSCILLATOR
(Pin 9)
An external RC network is connected to this input to set the fre-
quency of the Sawtooth Schmitt Trigger Oscillator. The Sawtooth
is applied to the PWM Comparator along with the output of the Er-
ror Amplifier. The output of the PWM Comparator is a Pulse
Width Modulated Signal which is used to vary the effective drive
to the motor and, hence, the motor speed.
OVERCURRENT SENSE
(Pins 10, 11)
The input to Pin 10 comes from the high side of a fractional ohm
current sensing resistor. The voltage at this input is compared to
an internal 100mV Reference. When the voltage exceeds the
100mV Reference, an Overcurrent Condition exists and the Out-
put Drivers are switched OFF until the end of the sawtooth os-
cillator ramp-up. When the sawtooth switches low, the Over-
current Condition is sampled, and if it no longer exists, the Output
Drivers are switched ON again. Otherwise, the Output Drivers re-
main OFF until the end of the next sawtooth. The input to Pin 11
comes from the low side (Gnd) of the current sensing resistor and
connects to the low side of the internal 100mV Reference.
PWM CONTROL Input
(Pin 21)
A High on this input causes only the Bottom Drivers to be Pulse
Width Modulated. A Low on this input causes both Top and Bot-
tom Drivers to have PWM.
TACHOMETER Output
(Pin 5)
The output of the Frequency To Pulse Width Converter is tied to
this pin. The Converter uses the three SENSOR Inputs and ex-
ternal RC Network to generate a variable frequency output with a
fixed positive pulse width.
RC Input
(Pin 4)
The external RC network connected to this input programs the
positive pulse width of the Frequency to Pulse Width Converter.
V
SS
(Pin 18)
V
SS
is Supply Voltage negative terminal.
MAXIMUM RATINGS
(Voltages referenced to Vss)
SYMBOL VALUE UNIT
Power Supply Voltage
V
DD
Voltage at any input
V
IN
Operating Temperature
T
A
Storage Temperature
T
STG
Output Drive Sink/Source Current
Io
V
R
Output Source Current
I
R
20
V
V
°C
°C
mA
mA
Vss-.5 to V
R
-25 to +85
-65 to +150
75
30
ELECTRICAL CHARACTERISTICS
V
DD
= 12V, R
T
= 47K
, C
T
= .001μF, R
S
= 10K
, C
S
= .01μF (See Figure 3) T
A
= 25°C, unless otherwise specified
PARAMETER SYMBOL MIN TYP MAX UNIT
Reference Voltage
V
R
Line Regulation
V
R
V
DD
= 10V to 18V, I
REF
=1.0mA
Temperature Stability
T
A =
0°C to 70°C
V
R
T
A =
0°C to 85°C
V
R
5.3
5.5
5.7
V
-
100
200
mV
-
-
+/- 1.0
+/- 1.3
-
-
%
%
Error Amplifier:
Input Offset Voltage
Input Current
Input Common Mode Voltage Range
Open Loop Voltage Gain (R
L
=15K
)
Common Mode Rejection Ratio
Power Supply Rejection Ratio
V
IO
I
IN
V
ICR
A
VOL
C
MRR
P
SRR
-
-
(0 to V
R
)
70
60
60
5
0
15
10
mV
nA
V
dB
dB
dB
80
-
-
-
-
-
相關PDF資料 |
PDF描述 |
|---|---|
| LS7560-TS | Controller Miscellaneous - Datasheet Reference |
| LS7561-S | Controller Miscellaneous - Datasheet Reference |
| LS7561-TS | Controller Miscellaneous - Datasheet Reference |
| LS7631-S | Analog Miscellaneous |
| LS7632-S | Analog Miscellaneous |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LS7560-TS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Controller Miscellaneous - Datasheet Reference |
| LS7561 | 制造商:LSI 制造商全稱:LSI 功能描述:BRUSHLESS DC MOTOR CONTROLLER |
| LS7561N | 制造商:LSI 制造商全稱:LSI 功能描述:BRUSHLESS DC MOTOR CONTROLLER |
| LS7561-S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Controller Miscellaneous - Datasheet Reference |
| LS7561-TS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Controller Miscellaneous - Datasheet Reference |
發布緊急采購，3分鐘左右您將得到回復。