參數資料
型號: LS7231-S
英文描述: Analog Miscellaneous
中文描述: 模擬雜項
文件頁數: 2/8頁
文件大?。?/td> 73K
代理商: LS7231-S
TABLE 1
TOUCH TYPE
SHORT (T
S1
Duration) LONG (T
S2
Duration)
PRE-TOUCH POST-TOUCH PRE-TOUCH POST-TOUCH
Off Max Off Starts varying at Min
Max Off Max Starts varying at Max
Intermediate Off Intermediate Starts varying at
Pre-Touch brightness
Off Memory Off Starts varying at
(Note 1) Memory (Note 2)
Max Off Max Starts varying at Max
Intermediate Off Intermediate Starts varying at
Pre-Touch brightness
Off Max Off Starts varying at Min
Max Off Max Starts varying at Max
Intermediate Off Intermediate Starts varying at
Pre-Touch brightness
Off Memory Off Starts varying at
(Note 1) Memory (Note 2)
Max Off Max Starts varying at Max
Intermediate Off Intermediate Starts varying at
Pre-Touch brightness
the Memory value defaults to maximum conduction angle.
NOTE 2:
First time after power-up, LONG touch causes intensity to vary starting at minimum conduction angle.
NOTE 3
: NO = Dimming direction does not reverse from prior dimming direction.
YES = Dimming direction does reverse from prior dimming direction.
N/A = Does not apply
SYNC
(Pin 4)
The AC Line Frequency is applied to this input through an
external RC circuit (See Figure 5). The Phase-Lock Loop
in the IC synchronizes all internal timings to the AC signal
at the SYNC input.
SENS
(Pin 5)
A low level activates this input (See Table 1) which con-
trols the turn-on, turn-off and conduction angle (See-
Figure 3) of the TRIG signal with respect to the SYNC in-
put.
EXT
(Pin 6)
The EXT input is functionally identical to the SENS input
except that a high level activates this input. It is rec-
ommended that the EXT input be used instead of the
SENS input when long extension wires are employed be-
tween the IC and the Sensing Circuitry (See Figure 5 and
Figure 6) because the EXT input is less susceptible to
“Noise”.
V
DD
(Pin 4)
Supply voltage negative terminal.
TRIG
(Pin 8)
The TRIG output is a low level pulse occurring once every
half-cycle of the SYNC input. The conduction angle, , of the
output in relation to the SYNC signal controls the lamp bright-
ness.
In continuous dimming operation (i.e. when the SENS input is
continuously held low) the TRIG conduction angle, , sweeps
up and down between 41 and 158 continuously. The time vs
curve is not linear (See Figure 2). Between two maxima on
this curve, there are 4 discontinuous points labeled A1, B1,
B2, A2. The discontinuities are as follows:
1. From maximum to A1. In this region, is changed by
equal increments (
) for every 2 SYNC clocks.
2. From A1 to B1. In this region, the increments (
) take
place for every 4 SYNC clocks.
3. From B1 to B2. In this region is held at a constant
level (
= 0).
4. From B2 to A2. Same as 2.
5. From A2 to Max. Same as 1.
The slower rate of change in over A1B1B2A2 region is to
accommodate for eye adjustment at lower light intensity.
The functional differences of different versions of the light dimmer ICs are explained in Table 1 and the TRIG
output conduction angle diagrams in Figure 2.
PART
NUMBER
LS7231
LS7232
LS7233
LS7234
DIMMING
DIRECTION
REVERSAL
(Note 3)
N/A
N/A
NO
YES
N/A
YES
N/A
N/A
YES
NO
N/A
NO
NOTE 1
: "Memory" refers to the conduction angle, which existed prior to the current off-state. First time after power-up,
7231-34-033195-2
相關PDF資料
PDF描述
LS7232 Analog Miscellaneous
LS7232NT-S Industrial Control IC
LS7232-S Analog Miscellaneous
LS7233 Analog Miscellaneous
LS7233-S Analog Miscellaneous
相關代理商/技術參數
參數描述
LS7232 制造商:LSI COMPUTER SYSTEMS 功能描述:TOUCH CONTROL SWITCH 7232 DIP8
LS7232 制造商:LSI COMPUTER SYSTEMS 功能描述:TOUCH CONTROL SWITCH 7232 DIP8
LS7232ND 制造商:LSI 制造商全稱:LSI 功能描述:TOUCH CONTROL LAMP DIMMER
LS7232NT 制造商:LSI 制造商全稱:LSI 功能描述:PROXIMITY/TOUCH CONTROL HALOGEN LAMP DIMMER
LS7232NT-S 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Industrial Control IC