- 您現在的位置：買賣IC網 > PDF目錄377657 > LQH31C (Linear Integrated Systems) Dual Micropower DC/DC Converters with Schottky Diodes PDF資料下載
參數資料
| 型號： | LQH31C |
| 廠商： | Linear Integrated Systems |
| 英文描述： | Dual Micropower DC/DC Converters with Schottky Diodes |
| 中文描述： | 雙微功率DC / DC轉換的肖特基二極管 |
| 文件頁數： | 6/8頁 |
| 文件大小： | 193K |
| 代理商： | LQH31C |
6
LT3463/LT3463A
3463f
inrush current include a larger more abrupt voltage step at
V
IN
, a larger output capacitor tied to the outputs, and an
inductor with a low saturation current.
While the internal diode is designed to handle such events,
the inrush current should not be allowed to exceed 1 amp.
For circuits that use output capacitor values within the
recommended range and have input voltages of less than
5V, inrush current remains low, posing no hazard to the
device. In cases where there are large steps at V
IN
and/or
a large capacitor is used at the outputs, inrush current
should be measured to ensure safe operation.
Setting the Output Voltages
The output voltages are programmed using two feedback
resistors. As shown in Figure 1, resistors R1 and R2
program the positive output voltage (for Switcher 1), and
resistors R3 and R4 program the negative output voltage
(for Switcher 2) according to the following formulas:
V
V
R
R
4
3
V
VR
R
OUT
OUT
1
2
1 25
.
1
2
1
–1 25
=
+
=
R1 and R3 are typically 1% resistors with values in the
range of 50k to 250k.
Board Layout Considerations
As with all switching regulators, careful attention must be
paid to the PCB board layout and component placement.
To maximize efficiency, switch rise and fall times are made
as short as possible. To prevent electromagnetic interfer-
ence (EMI) problems, proper layout of the high frequency
switching path is essential. The voltage signal of the SW
pin has sharp rising and falling edges. Minimize the length
and area of all traces connected to the SW pin and always
use a ground plane under the switching regulator to
minimize interplane coupling. In addition, the ground
connection for the feedback resistor R1 should be tied
directly to the GND pin and not shared with any other
component, ensuring a clean, noise-free connection.
APPLICATIU
output voltages from a high input voltage source will often
exceed the 50V maximum switch rating. For instance, a
12V to –40V converter using the inverting topology would
generate 52V on the SW pin, exceeding its maximum
rating. For this application, an inverting charge pump is
the best topology.
The formula below calculates the approximate inductor
value to be used for an inverting charge pump regulator
using the LT3463. As for the boost inductor selection, a
larger or smaller value can be used. For designs with
varying V
IN
such as battery powered applications, use the
minimum V
IN
value in the equation below.
W
U
U
L
V
V
V
I
t
OUT
IN MIN
D
LIM
OFF
=
+
)
Capacitor Selection
The small size and low ESR of ceramic capacitors makes
them ideal for LT3463 applications. Use only X5R and X7R
types because they retain their capacitance over wider
voltage and temperature ranges than other ceramic types.
A 1
μ
F input capacitor and a 0.22
μ
F or 0.47
μ
F output
capacitor are sufficient for most applications. Table 2
shows a list of several ceramic capacitor manufacturers.
Consult the manufacturers for more detailed information
on their entire selection of ceramic capacitors. For appli-
cations needing very low output voltage ripple, larger
output capacitor values can be used.
Table 2. Recommended Ceramic Capacitor Manufacturers
MANUFACTURER
PHONE
AVX
843-448-9411
Kemet
408-986-0424
Murata
814-237-1431
Taiyo Yuden
408-573-4150
URL
www.avxcorp.com
www.kemet.com
www.murata.com
www.t-yuden.com
Inrush Current
When V
IN
is increased from ground to operating voltage
while the output capacitor is discharged, an inrush current
will flow through the inductor and integrated Schottky
diode into the output capacitor. Conditions that increase
相關PDF資料 |
PDF描述 |
|---|---|
| LQH32C | Dual Micropower DC/DC Converters with Schottky Diodes |
| LQH3C100 | Dual Micropower DC/DC Converter with Positive and Negative Outputs |
| LQH3C220 | Dual Micropower DC/DC Converter with Positive and Negative Outputs |
| LQH3C4R7 | Dual Micropower DC/DC Converter with Positive and Negative Outputs |
| LQH4C470K04M00 | 1.0MHz Inverting DC/DC Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LQH31CN100 | 制造商:DIODES 制造商全稱:Diodes Incorporated 功能描述:ADJUSTABLE DC - DC BOOST CONVERTER WITH INTERNAL SWITCH |
| LQH31CN100K01L | 功能描述:固定電感器 1206 10uH 10% RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| LQH31CN100K03 | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:Chip Inductor (Chip Coil) Power Inductor (Wire Wound Type for Choke) LQH31C Series (1206 Size) |
| LQH31CN100K03L | 功能描述:固定電感器 10uH 10% RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| LQH31CN101K01L | 功能描述:固定電感器 1206 100uH 10% RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
發布緊急采購，3分鐘左右您將得到回復。