- 您現在的位置：買賣IC網 > PDF目錄67757 > LPY450ALTR (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBCC28 PDF資料下載
參數資料
| 型號： | LPY450ALTR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBCC28 |
| 封裝： | 4 X 5 MM, 1 MM HEIGHT, GREEN, PLASTIC, LGA-28 |
| 文件頁數： | 13/14頁 |
| 文件大?。?/td> | 278K |
| 代理商： | LPY450ALTR |
Terminology
LPY450AL
8/14
Doc ID 16580 Rev 1
4
Terminology
4.1
Sensitivity
An angular rate gyroscope is a device that produces a positive-going output voltage for
counterclockwise rotation around the sensitive axis considered. Sensitivity describes the
gain of the sensor and can be determined by applying a defined angular velocity to it. This
value changes very little over temperature and time.
4.2
Zero-rate level
Zero-rate level describes the actual output signal if there is no angular rate present. The
zero-rate level of precise MEMS sensors is, to some extent, a result of stress to the sensor
and therefore zero-rate level can slightly change after mounting the sensor onto a printed
circuit board or after exposing it to extensive mechanical stress. This value changes very
little over temperature and time.
4.3
Self-test
Self-test allows testing of the mechanical and electrical part of the sensor, allowing the
seismic mass to be moved by means of an electrostatic test-force. The self-test function is
off when the ST pin is connected to GND. When the ST pin is tied to Vdd, an actuation force
is applied to the sensor, emulating a definite Coriolis force. In this case the sensor output
exhibits a voltage change in its DC level which is also dependent on the supply voltage.
When ST is active, the device output level is given by the algebraic sum of the signals
produced by the velocity acting on the sensor and by the electrostatic test-force. If the output
signals change within the amplitude specified in
Table 3, then the mechanical element is
working properly and the parameters of the interface chip are within the defined
specifications.
4.4
High pass filter reset (HP)
The LPY450AL provides the possibility to reset the optional external high-pass filter by
applying a high logic value to the HP pad. This procedure ensures faster response,
especially during overload conditions. Moreover, this operation is recommended each time
the device is powered.
4.5
Sleep mode, self-test and power-down
The LPY450AL enables advanced power-saving features thanks to the availability of three
different operating modes. When the device is set in a Sleep mode configuration, the
reading chain is completely turned off, resulting in low power consumption. In this condition
the device turn-on time is significantly reduced, allowing simple external power cycling.
In accordance with the table below, the user can select the desired operating mode using
two dedicated pins (ST and SLEEP/PD).
相關PDF資料 |
PDF描述 |
|---|---|
| LPY450AL | SPECIALTY ANALOG CIRCUIT, PBCC28 |
| LSN2-T/16-D12NGC | DC-DC REG PWR SUPPLY MODULE |
| LSP3601SAH | SWITCHING CONTROLLER, 600 kHz SWITCHING FREQ-MAX, PDSO8 |
| LSP3601TSAH | SWITCHING CONTROLLER, 600 kHz SWITCHING FREQ-MAX, PDSO8 |
| LSP3601TSH | SWITCHING CONTROLLER, 600 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPY503AL | 功能描述:螺旋儀 Dual 8.3 mV deg/s LGA-16 RoHS:否 制造商:Murata 傳感軸:Triple 靈敏度: 輸出類型:Digital 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:5 mA 封裝 / 箱體: |
| LPY503ALTR | 功能描述:螺旋儀 MEMS 30 / 120 2.7V to 3.6V PS RoHS:否 制造商:Murata 傳感軸:Triple 靈敏度: 輸出類型:Digital 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:5 mA 封裝 / 箱體: |
| LPY510AL | 功能描述:螺旋儀 Dual 2.5 mV deg/s LGA-16 RoHS:否 制造商:Murata 傳感軸:Triple 靈敏度: 輸出類型:Digital 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:5 mA 封裝 / 箱體: |
| LPY510ALTR | 功能描述:螺旋儀 MEMS 100 / 400 2.7V to 3.6V PS RoHS:否 制造商:Murata 傳感軸:Triple 靈敏度: 輸出類型:Digital 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:5 mA 封裝 / 箱體: |
| LPY5150AL | 功能描述:螺旋儀 Dual 0.167 mV deg/s LGA-16 RoHS:否 制造商:Murata 傳感軸:Triple 靈敏度: 輸出類型:Digital 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:5 mA 封裝 / 箱體: |
發布緊急采購，3分鐘左右您將得到回復。