參數資料
型號： LPC2377FBD144
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： Single-chip 16-bit-32-bit microcontrollers; 512 kB flash with ISP-IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC-DAC
中文描述： 32-BIT, FLASH, 25 MHz, RISC MICROCONTROLLER, PQFP144
封裝： 20 X 20 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT486-1, LQFP-144
文件頁數： 33/68頁
文件大小： 1443K
代理商： LPC2377FBD144
LPC2377_78
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 5 — 17 June 2010
33 of 68
NXP Semiconductors
LPC2377/78
Single-chip 16-bit/32-bit microcontrollers
sufficient amplitude to drive the clock logic. The amount of time depends on many factors,
including the rate of V
DD(3V3)
ramp (in the case of power on), the type of crystal and its
electrical characteristics (if a quartz crystal is used), as well as any other external circuitry
(e.g., capacitors), and the characteristics of the oscillator itself under the existing ambient
conditions.
7.25.4
Power control
The LPC2377/78 support a variety of power control features. There are four special
modes of processor power reduction: Idle mode, Sleep mode, Power-down mode, and
Deep power-down mode. The CPU clock rate may also be controlled as needed by
changing clock sources, reconfiguring PLL values, and/or altering the CPU clock divider
value. This allows a trade-off of power versus processing speed based on application
requirements. In addition, Peripheral Power Control allows shutting down the clocks to
individual on-chip peripherals, allowing fine tuning of power consumption by eliminating all
dynamic power use in any peripherals that are not required for the application. Each of the
peripherals has its own clock divider which provides even better power control.
The LPC2377/78 also implement a separate power domain in order to allow turning off
power to the bulk of the device while maintaining operation of the RTC and a small SRAM,
referred to as the battery RAM.
7.25.4.1
Idle mode
In Idle mode, execution of instructions is suspended until either a Reset or interrupt
occurs. Peripheral functions continue operation during Idle mode and may generate
interrupts to cause the processor to resume execution. Idle mode eliminates dynamic
power used by the processor itself, memory systems and related controllers, and internal
buses.
7.25.4.2
Sleep mode
In Sleep mode, the oscillator is shut down and the chip receives no internal clocks. The
processor state and registers, peripheral registers, and internal SRAM values are
preserved throughout Sleep mode and the logic levels of chip pins remain static. The
output of the IRC is disabled but the IRC is not powered down for a fast wake-up later. The
32 kHz RTC oscillator is not stopped because the RTC interrupts may be used as the
wake-up source. The PLL is automatically turned off and disconnected. The CCLK and
USB clock dividers automatically get reset to zero.
The Sleep mode can be terminated and normal operation resumed by either a Reset or
certain specific interrupts that are able to function without clocks. Since all dynamic
operation of the chip is suspended, Sleep mode reduces chip power consumption to a
very low value. The flash memory is left on in Sleep mode, allowing a very quick wake-up.
On the wake-up of Sleep mode, if the IRC was used before entering Sleep mode, the
code execution and peripherals activities will resume after 4 cycles expire. If the main
external oscillator was used, the code execution will resume when 4096 cycles expire.
The customers need to reconfigure the PLL and clock dividers accordingly.
相關PDF資料
PDF描述
LPC2378FBD144 Single-chip 16-bit-32-bit microcontrollers; 512 kB flash with ISP-IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC-DAC
LPC2387FBD100 Single-chip 16-bit-32-bit MCU; 512 kB flash with ISP-IAP, Ethernet, USB 2.0 device-host-OTG, CAN, and 10-bit ADC-DAC
LPC2388FBD144 Single-chip 16-bit-32-bit micro; 512 kB flash with ISP-IAP, Ethernet, USB 2.0 device-host-OTG, CAN, and 10-bit ADC-DAC
LPC2420FBD208 Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface
LPC2420FET208 Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface
相關代理商/技術參數
參數描述
LPC2377FBD144,551 功能描述:ARM微控制器 - MCU 16/32 bit micro RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2378 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16-bit/32-bit microcontrollers; 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
LPC2378FBD144 制造商:NXP Semiconductors 功能描述:MCU 32BIT ARM7 10/100 USB CAN 制造商:NXP Semiconductors 功能描述:MCU 32BIT ARM7, 10/100, USB, CAN
LPC2378FBD144,551 功能描述:ARM微控制器 - MCU ARM7 512KF/USB/ENET RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2378FBD144/CP32 制造商:NXP Semiconductors 功能描述:- Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*