參數資料
型號: LPC2364
廠商: NXP Semiconductors N.V.
英文描述: Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
中文描述: 單芯片16-bit/32-bit微控制器,高達512的ISP /國際檢察官聯合會,以太網,USB 2.0,CAN和10 kB閃存位的ADC / DAC
文件頁數: 27/48頁
文件大小: 377K
代理商: LPC2364
LPC2364_66_68_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Preliminary data sheet
Rev. 01 — 22 September 2006
27 of 48
Philips Semiconductors
LPC2364/2366/2368
Fast communication chip
7.24.1.1
Internal RC oscillator
The Internal RC oscillator (IRC) may be used as the clock source for the watchdog timer,
and/or as the clock that drives the PLL and subsequently the CPU. The nominal IRC
frequency is 4 MHz. The IRC is trimmed to 1 % accuracy.
Upon power-up or any chip reset, the LPC2364/66/68 uses the IRC as the clock source.
Software may later switch to one of the other available clock sources.
7.24.1.2
Main oscillator
The main oscillator can be used as the clock source for the CPU, with or without using the
PLL. The main oscillator operates at frequencies of 1 MHz to 24 MHz. This frequency can
be boosted to a higher frequency, up to the maximum CPU operating frequency, by the
PLL. The oscillator output is called OSCCLK. The clock selected as the PLL input is
PLLCLKIN, and the ARM processor clock frequency is referred to as CCLK elsewhere in
this document. The frequencies of PLLCLKIN and CCLK are the same value unless the
PLL is active and connected. Refer to
Section 7.24.2
for additional information.
7.24.1.3
RTC oscillator
The RTC oscillator can be used as the clock source for the RTC and/or the watchdog
timer. Also, the RTC oscillator can be used to drive the PLL and the CPU.
7.24.2
PLL
The PLL accepts an input clock frequency in the range of 31 kHz to 50 MHz. The input
frequency is multiplied up to a high frequency, then divided down to provide the actual
clock used by the CPU and the USB block.
The PLL input, in the range of 32 kHZ to 50 MHz, may initially be divided down by a value
‘N’, which may be in the range of 1 to 256. This input division provides a wide range of
output frequencies from the same input frequency.
Following the PLL input divider is the PLL multiplier. This can multiply the input divider
output through the use of a Current Controlled Oscillator (CCO) by a value ‘M’, in the
range of 1 through 32768. The resulting frequency must be in the range of 275 MHz to
550 MHz. The multiplier works by dividing the CCO output by the value of M, then using a
phase-frequency detector to compare the divided CCO output to the multiplier input. The
error value is used to adjust the CCO frequency.
The PLL is turned off and bypassed following a chip Reset and by entering Power-down
mode. PLL is enabled by software only. The program must configure and activate the PLL,
wait for the PLL to Lock, then connect to the PLL as a clock source.
7.24.3
Wake-up timer
The LPC2364/66/68 begins operation at power-up and when awakened from Power-down
mode or Deep power-down mode by using the 4 MHz IRC oscillator as the clock source.
This allows chip operation to resume quickly. If the main oscillator or the PLL is needed by
the application, software will need to enable these features and wait for them to stabilize
before they are used as a clock source.
When the main oscillator is initially activated, the wake-up timer allows software to ensure
that the main oscillator is fully functional before the processor uses it as a clock source
and starts to execute instructions. This is important at power on, all types of Reset, and
相關PDF資料
PDF描述
LPC2366 Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
LPC2366FB100 Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
LPC2368 Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
LPC2368FB100 Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
LPC2378 Single-chip 16-bit/32-bit microcontrollers; 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
相關代理商/技術參數
參數描述
LPC2364_10 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
LPC2364FB100 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
LPC2364FBD100 制造商:NXP Semiconductors 功能描述:MCU 32BIT ARM7 10/100 USB CAN 制造商:NXP Semiconductors 功能描述:MCU 32BIT ARM7, 10/100, USB, CAN 制造商:NXP Semiconductors 功能描述:IC, 32BIT MCU, ARM7, 72MHZ, LQFP-100; Controller Family/Series:(ARM7); Core Size:32bit; No. of I/O's:70; Supply Voltage Min:3V; Supply Voltage Max:3.6V; Digital IC Case Style:LQFP; No. of Pins:100; Program Memory Size:128KB ;RoHS Compliant: Yes 制造商:NXP Semiconductors 功能描述:Microcontroller,LPC2364FBD100 72 MHz
LPC2364FBD100,551 功能描述:ARM微控制器 - MCU ARM7 128KF/USB/ENET RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2364FBD100551 制造商:NXP Semiconductors 功能描述:IC 32BIT MCU 72MHZ LQFP-100