- 您現在的位置：買賣IC網 > PDF目錄385497 > LPC2158FBD100 (NXP SEMICONDUCTORS) Single-chip 16-bit-32-bit microcontrollers; 512 kB flash, with 32 segment x 4 LCD driver PDF資料下載
參數資料
| 型號： | LPC2158FBD100 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Single-chip 16-bit-32-bit microcontrollers; 512 kB flash, with 32 segment x 4 LCD driver |
| 中文描述： | 32-BIT, FLASH, 60 MHz, RISC MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 14 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT407-1, LQFP-100 |
| 文件頁數： | 25/45頁 |
| 文件大?。?/td> | 220K |
| 代理商： | LPC2158FBD100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
LPC2157_2158_2
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 02 — 9 February 2009
25 of 45
NXP Semiconductors
LPC2157/2158
Single-chip 16-bit/32-bit microcontrollers
6.19.4
Brownout detector
The LPC2157/2158 include 2-stage monitoring of the voltage on the V
DD
pins. If this
voltage falls below 2.9 V, the BOD asserts an interrupt signal to the VIC. This signal can
be enabled for interrupt; if not, software can monitor the signal by reading dedicated
register.
The second stage of low voltage detection asserts reset to inactivate the LPC2157/2158
when the voltage on the V
DD
pins falls below 2.6 V. This reset prevents alteration of the
flash as operation of the various elements of the chip would otherwise become unreliable
due to low voltage. The BOD circuit maintains this reset down below 1 V, at which point
the POR circuitry maintains the overall reset.
Both the 2.9 V and 2.6 V thresholds include some hysteresis. In normal operation, this
hysteresis allows the 2.9 V detection to reliably interrupt, or a regularly-executed event
loop to sense the condition.
6.19.5
Code security
This feature of the LPC2157/2158 allow an application to control whether it can be
debugged or protected from observation.
If after reset on-chip bootloader detects a valid checksum in flash and reads 0x8765 4321
from address 0x1FC in flash, debugging will be disabled and thus the code in flash will be
protected from observation. Once debugging is disabled, it can be enabled only by
performing a full chip erase using the ISP.
6.19.6
External interrupt inputs
The LPC2157/2158 include up to nine edge or level sensitive external interrupt inputs as
selectable pin functions. When the pins are combined, external events can be processed
as four independent interrupt signals. The external interrupt inputs can optionally be used
to wake-up the processor from Power-down mode.
Additionally capture input pins can also be used as external interrupts without the option
to wake the device up from Power-down mode.
6.19.7
Memory mapping control
The Memory Mapping Control alters the mapping of the interrupt vectors that appear
beginning at address 0x0000 0000. Vectors may be mapped to the bottom of the on-chip
flash memory, or to the on-chip static RAM. This allows code running in different memory
spaces to have control of the interrupts.
6.19.8
Power control
The LPC2157/2158 supports two reduced power modes: Idle mode and Power-down
mode.
In Idle mode, execution of instructions is suspended until either a reset or interrupt occurs.
Peripheral functions continue operation during Idle mode and may generate interrupts to
cause the processor to resume execution. Idle mode eliminates power used by the
processor itself, memory systems and related controllers, and internal buses.
相關PDF資料 |
PDF描述 |
|---|---|
| LPC2194HBD64 | Single-chip 16-32-bit microcontroller; 256 kB ISP-IAP flash with 10-bit ADC and CAN |
| LPC2210FBD144 | 16-32-bit ARM microcontrollers; flashless, with 10-bit ADC and external memory interface |
| LPC2220FET144 | 16-32-bit ARM microcontrollers; flashless, with 10-bit ADC and external memory interface |
| LPC2212FBD144 | Single-chip 16-32-bit ARM microcontrollers; 128-256 kB ISP-IAP flash with 10-bit ADC and external memory interface |
| LPC2214FBD144 | Single-chip 16-32-bit ARM microcontrollers; 128-256 kB ISP-IAP flash with 10-bit ADC and external memory interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC2158FBD100,551 | 功能描述:ARM微控制器 - MCU 512K FL/40K RAM RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC2158FBD100-S | 功能描述:ARM微控制器 - MCU 512K FL/40K RAM USB LCD RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC2194 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16/32-bit microcontroller; 256 kB ISP/IAP flash with 10-bit ADC and CAN |
| LPC2194HBD64 | 制造商:NXP Semiconductors 功能描述:MCU 32BIT ARM7 256K FLASH LQFP64 |
| LPC2194HBD64,151 | 功能描述:ARM微控制器 - MCU PREF PART LPC2194HBD64/01-S RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。