- 您現在的位置：買賣IC網 > PDF目錄224109 > LP3918TL-L (NATIONAL SEMICONDUCTOR CORP) Battery Charge Management and Regulator Unit PDF資料下載
參數資料
| 型號： | LP3918TL-L |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Battery Charge Management and Regulator Unit |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PBGA25 |
| 封裝： | 2.50 X 2.50 MM, MICRO, SMD-25 |
| 文件頁數： | 19/30頁 |
| 文件大?。?/td> | 1292K |
| 代理商： | LP3918TL-L |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
20211613
FIGURE 6. Bit Transfer
Each data transaction is composed of a Start Condition, a
number of byte transfers (set by the software) and a Stop
Condition to terminate the transaction. Every byte written to
the SDA bus must be 8 bits long and is transferred with the
most significant bit first. After each byte, an Acknowledge sig-
nal must follow. The following sections provide further details
of this process.
START AND STOP
The Master device on the bus always generates the Start and
Stop Conditions (control codes). After a Start Condition is
generated, the bus is considered busy and it retains this sta-
tus until a certain time after a Stop Condition is generated. A
high-to-low transition of the data line (SDA) while the clock
(SCL) is high indicates a Start Condition. A low-to-high tran-
sition of the SDA line while the SCL is high indicates a Stop
Condition.
20211610
FIGURE 7. Start and Stop Conditions
In addition to the first Start Condition, a repeated Start Con-
dition can be generated in the middle of a transaction. This
allows another device to be accessed, or a register read cycle.
ACKNOWLEDGE CYCLE
The Acknowledge Cycle consists of two signals: the acknowl-
edge clock pulse the master sends with each byte transferred,
and the acknowledge signal sent by the receiving device.
The master generates the acknowledge clock pulse on the
ninth clock pulse of the byte transfer. The transmitter releases
the SDA line (permits it to go high) to allow the receiver to
send the acknowledge signal. The receiver must pull down
the SDA line during the acknowledge clock pulse and ensure
that SDA remains low during the high period of the clock
pulse, thus signaling the correct reception of the last data byte
and its readiness to receive the next byte.
20211628
FIGURE 8. Bus Acknowledge Cycle
“ACKNOWLEDGE AFTER EVERY BYTE” RULE
The master generates an acknowledge clock pulse after each
byte transfer. The receiver sends an acknowledge signal after
every byte received.
There is one exception to the “acknowledge after every byte”
rule.
When the master is the receiver, it must indicate to the trans-
mitter an end of data by not-acknowledging (“negative ac-
knowledge”) the last byte clocked out of the slave. This
“negative acknowledge” still includes the acknowledge clock
pulse (generated by the master), but the SDA line is not pulled
down.
ADDRESSING TRANSFER FORMATS
Each device on the bus has a unique slave address. The
LP3918 operates as a slave device with the address 7h’7E
(binary 1111110). Before any data is transmitted, the master
transmits the address of the slave being addressed. The slave
device should send an acknowledge signal on the SDA line,
once it recognizes its address.
The slave address is the first seven bits after a Start Condi-
tion. The direction of the data transfer (R/W) depends on the
bit sent after the slave address — the eighth bit.
When the slave address is sent, each device in the system
compares this slave address with its own. If there is a match,
the device considers itself addressed and sends an acknowl-
edge signal. Depending upon the state of the R/W bit (1:read,
0:write), the device acts as a transmitter or a receiver.
www.national.com
26
LP3918
相關PDF資料 |
PDF描述 |
|---|---|
| LP3918TLX-L | Battery Charge Management and Regulator Unit |
| LPB-5015 | PULSE TRANSFORMER FOR GENERAL PURPOSE APPLICATION(S) |
| LPC870-F2G2-1 | SINGLE COLOR LED, PURE GREEN |
| LPD3015-682MTD | 2 ELEMENT, 6.8 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| LPD3015-682MSD | 2 ELEMENT, 6.8 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LP3918TLX | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
| LP3918TLX/NOPB | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| LP3918TLX-A | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Battery Charge Management and Regulator Unit |
| LP3918TLX-A/NOPB | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| LP3918TLX-L | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Battery Charge Management and Regulator Unit |
發布緊急采購，3分鐘左右您將得到回復。