- 您現在的位置：買賣IC網 > PDF目錄367582 > LOR4801-2RLD DIN-Rail Mountable AC-DC (DC-DC) Converters PDF資料下載
參數資料
| 型號： | LOR4801-2RLD |
| 英文描述： | DIN-Rail Mountable AC-DC (DC-DC) Converters |
| 中文描述： | 導軌可安裝交直流（型DC - DC）轉換器 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 155K |
| 代理商： | LOR4801-2RLD |
SEP 09, 2005 revised to JUL 17, 2006
Page 9 of 12
www.power-one.com
LOS, LOR, LOK4000 Series Data Sheet
DIN-Rail Mountable AC-DC (DC-DC) Converters
Installation Instructions
These converters are components, intended exclusively for
inclusion within other equipment by an industrial assembly
operation or by professional installers. Installation must strictly
follow the national safety regulations in compliance with the
enclosure, mounting, creepage, clearance, casualty, markings
and segregation requirements of the end-use application.
Connection to the system shall be according to
Terminal
allocation
and
Mechanical Data
. Check for hazardous voltages
before altering any connection.
Ensure that a converter failure (e.g. by an internal short-circuit)
does not result in a hazardous condition. See also
Safety of
operator accessible output circuit
.
The phase input (
L
) is internally fused by a 1.6 A slowblow
type. It is not customer-accessible. This fuse is designed to
protect the unit in case of overcurrent. Option F or external
fuses in the wiring to one or both input pins (
L
and/or
N
) may
therefore be necessary to ensure compliance with local
requirements.
A second fuse in the wiring to the terminal
N
is needed if:
Local requirements demand an individual fuse in each
source line
Neutral and earth impedance is high or undefined
Phase and neutral of the mains are not defined or cannot be
assigned to the corresponding termials (
L
to phase and
N
to neutral).
Note:
Do not open the converters, or guarantee will be invalidated.
Make sure that there is sufficient air flow available for
convection cooling. This should be verified by measuring the
case temperature when the unit is installed and operated in the
end-use
application.
The
temperature
T
C max
shall not be exceeded.
maximum
specified
case
Isolation
The electric strength test is performed in the factory as routine
test in accordance with EN 50116 and IEC/EN 60950and
should not be repeated in the field. Power-One will not honor
any guarantee/warranty claims resulting from electric strength
field tests.
Caution:
Testing by applying AC voltages will result in high and
dangerous leakage currents flowing through the Y-capacitors
(see fig.
Block diagram).
Safety and Installation Instructions
Terminal Allocation
The terminal allocation table defines the electrical potentials of
the AC-DC converters. For mechanical positions of the
terminals see:
Mechanical Data
.
Standards and Approvals
The converters correspond to class I equipment. All models
are UL recognized according to UL 1950, UL recognized for
Canada to CAN/CSA C22.2 No. 950-95 and TüV, approved to
IEC/EN 60950 standards.
LOR and LOS are UL 508-listed components.
The converters have been evaluated for:
Building in
Double or reinforced insulation or an earthed part between
input and output.
Basic insulation between input and earth
Functional insulation between output and earth
The use in a pollution degree 2 environment
Connecting the input to a primary circuit with overvoltage
category II.
The converters are subject to manufacturing surveillance in
accordance with the above mentioned standards.
For details see the Declaration of Conformity (last 2 pages).
Protection Degree
IP 20: All models.
Table 9: Terminal allocation
Terminal
Electrical
LOK/LOR/LOS
1
Input
L
2
Protective earth
3
Input
N
4
D/Output (positive)
D/+
5
Output (positive)
+
6
Output (negative)
–
7
Output (negative)
–
8
R input or open
R/n.c.
Table 10: Isolation
Characteristic
Input to
Input to
output
Output to
protective earth
Unit
protective earth
Electric
strength
test voltage
Actual factory test 1 s
2.1
2.1
1
1.4
kVDC
AC test voltage equivalent
to actual factory test
1.5
1.5
1
1.0
kVAC
Insulation resistance at 500 VDC
>
300
>
300
>
100
M
1
In accordance with EN 50116 and IEC/EN 60950 only subassemblies are pre-tested with 4.3 kVDC or 3.0 kVAC.
相關PDF資料 |
PDF描述 |
|---|---|
| LOS4001-2RLD | DIN-Rail Mountable AC-DC (DC-DC) Converters |
| LOS4140-2RLD | DIN-Rail Mountable AC-DC (DC-DC) Converters |
| LOS4240-2RLD | DIN-Rail Mountable AC-DC (DC-DC) Converters |
| LOS4301-2RLD | DIN-Rail Mountable AC-DC (DC-DC) Converters |
| LOS4601-2RLD | DIN-Rail Mountable AC-DC (DC-DC) Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LOR5.LV318-R0025-D | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:PRECISION LOW-OHM METAL PLATE RESISTORS |
| LOR5.LV318-R0025-F | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:PRECISION LOW-OHM METAL PLATE RESISTORS |
| LOR5.LV318-R0025-G | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:PRECISION LOW-OHM METAL PLATE RESISTORS |
| LOR5.LV318-R0025-H | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:PRECISION LOW-OHM METAL PLATE RESISTORS |
| LOR5.LV318-R0025-J | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:PRECISION LOW-OHM METAL PLATE RESISTORS |
發布緊急采購，3分鐘左右您將得到回復。