- 您現在的位置：買賣IC網 > PDF目錄44516 > LMZ1501-9PD2AHFU 1-OUTPUT AC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | LMZ1501-9PD2AHFU |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
| 封裝： | 168.50 X 111.20 MM, 38.70 MM HEIGHT, METAL, CASE M02, MODULE |
| 文件頁數： | 18/24頁 |
| 文件大?。?/td> | 536K |
| 代理商： | LMZ1501-9PD2AHFU |
M-Family
DC-DC Converters <100 W
Rugged Environment
7 - 4
Edition 2/96 - Melcher AG
MELCHER
The Power Partners.
7.1
Safety and Installation Instructions
Safety
For safety reasons, the power supply modules must be wired via the female connector H11 (according to DIN 41612,
see section "Accessories") in order to meet national and international safety requirements!
If the output circuit of a DC-DC converter is operator-acces-
sible according to the IEC 950 related safety standards, it
shall be an SELV circuit (Safety Extra Low Voltage circuit,
i.e. a circuit, separated from mains by at least basic insula-
tion, that is so designed and protected that under normal
and single fault conditions, the voltage between any two
conductors and between any conductor and earth does not
exceed 60 V DC).
In the following section an interpretation is provided of the
IEC 950 safety standard with respect to the safety status of
the output circuit. However, it is the sole responsibility of the
installer or user to assure the compliance with the relevant
and applicable safety standards.
Since the M-family DC-DC converters provide double or re-
inforced insulation between input and output, based on an
input voltage of 250 V AC and 400 V DC, only operational
insulation between the AC mains and the input of the DC-
DC converter is needed according to the following table.
If the table below is observed, the output of a DC-DC con-
verter is considered to be an SELV circuit up to a nominal
output voltage of 36 V.
Table 3: Insulation concept
Nominal
Minimum required grade of
Maximum Minimum required safety
Minimum required grade
Resulting
mains
isolation, to be provided by
output
status of the front end
of isolation between the
safety
supply
the AC-DC front end,
voltage
output circuit
input and the output
status
voltage
including mains supplied
from the
provided by the
of the
(AC)
battery charger
front end
DC-DC converter
DC-DC
output
≤250V
Operational
≤400 V 1
Primary circuit
Reinforced, based on
SELV
AC 250 V and DC 400 V 1
circuit
1 With LMZ converters, the maximum rated output voltage of the front end is 250 V according to IEC 950.
AM...LM types correspond to class I equipment, while the
C/D/ LMZ types correspond to class II equipment.
In class I equipment the connector protective earthing pin is
leading while it is omitted in class II equipment (no protec-
tive earthing is required). Class II equipment provides rein-
forced insulation between input and output circuitry and
also between input and case. There are two class II Y-ca-
pacitors connected in series between input and output cir-
cuitry instead of having Y-capacitors connected to the case.
During the production process, all transformers and each of
the fully assembled modules are individually tested for elec-
tric strength and earth continuity (see "Supplementary
Data"). All electric strength tests are performed as factory
tests.
The UL 1950 recognition limits the maximum ambient op-
erational temperature of the standard modules to
TA =
TA max –15 K. Option U allows the operation in applications
where the full operational temperature range according to
the relevant data sheet and UL 1950 recognition is re-
quired.
Important Advice
Electric strength tests should not be repeated in the field. Improper test methods, for example overshooting or oscillating
test voltages, voltage slopes exceeding 1 kV/
s, internal Y-capacitors not carefully discharged, etc. can cause severe
damage to switching devices and ICs. Melcher AG will not honour any guarantee/warranty claims resulting from high
voltage field tests.
相關PDF資料 |
PDF描述 |
|---|---|
| LMZ1601-7ERD3AHFU | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
| LMZ1601-7RD8AHFU | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
| LMZ1601-9ERD0AHFU | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
| LMZ1901-7EPD3AHFU | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
| LMZ1901-7PD2AHFU | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMZ1601-7R | 制造商:POWER-ONE 制造商全稱:Power-One 功能描述:50 Watt AC-DC Converters |
| LMZ1901-7R | 制造商:POWER-ONE 制造商全稱:Power-One 功能描述:50 Watt AC-DC Converters |
| LMZ20501EVM | 功能描述:LMZ20501 SIMPLE SWITCHER? DC/DC, Step Down 1, Non-Isolated Outputs Evaluation Board 制造商:texas instruments 系列:SIMPLE SWITCHER? 零件狀態:有效 主要用途:DC/DC，步降 輸出和類型:1，非隔離 功率 - 輸出:- 電壓 - 輸出:1.8V 電流 - 輸出:1A 電壓 - 輸入:2.7 V ~ 5.5 V 穩壓器拓?fù)?降壓 頻率 - 開關:3MHz 板類型:完全填充 所含物品:板 使用的 IC/零件:LMZ20501 標準包裝:1 |
| LMZ20501SILR | 功能描述:DC/DC CONVERTER 0.8-3.6V 4W 制造商:texas instruments 系列:SIMPLE SWITCHER? Nano 包裝:剪切帶（CT） 零件狀態:有效 類型:非隔離 PoL 模塊 輸出數:1 電壓 - 輸入（最小值）:2.7V 電壓 - 輸入（最大值）:5.5V 電壓 - 輸出 1:0.8 ~ 3.6 V 電壓 - 輸出 2:- 電壓 - 輸出 3:- 電流 - 輸出（最大值）:1A 功率（W） - 制造系列:- 電壓 - 隔離:- 應用:ITE（商業） 特性:遠程開/關，OCP，OTP，SCP，UVLO 安裝類型:表面貼裝 封裝/外殼:8-SMD 模塊 大小/尺寸:0.14" 長 x 0.14" 寬 x 0.07" 高（3.5mm x 3.5mm x 1.8mm） 工作溫度:-40°C ~ 125°C 效率:93% 功率（W） - 最大值:4W 標準包裝:1 |
| LMZ20501SILT | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。