- 您現在的位置：買賣IC網 > PDF目錄367574 > LMX2331LTMX Serial-Input Frequency Synthesizer PDF資料下載
參數資料
| 型號： | LMX2331LTMX |
| 英文描述： | Serial-Input Frequency Synthesizer |
| 中文描述： | 串行輸入頻率合成器 |
| 文件頁數： | 15/19頁 |
| 文件大?。?/td> | 362K |
| 代理商： | LMX2331LTMX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁
1.7 Application Information
1.7.1 DEVICE PROGRAMMING AFTER FIRST
APPLYING V
CC
Three MICROWIRE programming methods can be used to
change the function latch, R counter latch, and N counter
latch contents with close phase alignment of R and N
counters to minimize lock up time after the cold power up.
1.7.2 INITIALIZATION SEQUENCE METHOD
Loading the function latch with [C1, C2] = [1, 1] immediately
followed by an R counter load, then an N counter load, effi-
ciently programs the MICROWIRE. Loading the function
latch with [C1, C2] = [1, 1] programs the same function latch
as a load with [C1, C2] = [0, 1] and additionally provides an
internal reset pulse described below. This program se-
quence insures that the counters are at load point when the
N counter data is latched in and the part will begin counting
in close phase alignment.
The following results from latching the MICROWIRE with an
F latch word, [C1, C2] = [1, 1]:
The function latch contents are loaded.
An internal pulse resets the R, N, and timeout counters to
load state conditions and will TRI-STATE the charge
pump. If the function latch is programmed for the syn-
chronous powerdown case; CE = HIGH, F[2] = HIGH,
F[18] = HIGH, this internal pulse triggers powerdown.
Refer to Section 1.3.1 POWERDOWN OPERATION sec-
tion for a synchronous powerdown description. Note that
the prescaler bandgap reference and the oscillator input
buffer are unaffected by the internal reset pulse, allowing
close phase alignment when counting resumes.
Latching the first N counter data after the initialization
word will activate the same internal reset pulse. Succes-
sive N counter data loads without an initialization load will
not trigger the internal reset pulse.
1.7.3 CE METHOD
Programming the function latch, R counter latch and N
counter latch while the part is being held in a powerdown
state by CE allows lowest possible power dissipation. After
the MICROWIRE contents have been programmed and the
part is enabled, the R and N counter contents will resume
counting in close phase alignment. Note that after CE transi-
tions from LOW to HIGH, a duration of 1 μs may be required
for the prescaler bandgap voltage and oscillator input buffer
bias to reach steady state.
CE can be used to power the part up and down by pin control
in order to check for channel activity. The MICROWIRE does
not need to be reprogrammed each time the part is enabled
and disabled as long as it has been programmed at least
once after V
CC
was applied.
1.7.4 COUNTER RESET METHOD
This MICROWIRE programming method consists of a func-
tion latch load, [C1, C2] = [0, 1], enabling the counter reset
bit, F[1]. The R and N counter latches are then loaded fol-
lowed by a final function latch load that disables the counter
reset. This provides the same close phase alignment as the
initialization sequence method with direct control over the in-
ternal reset. Note that counter reset holds the counters at
load point and will TRI-STATE the charge pump, but does
not trigger synchronous powerdown. The counter reset
method requires an extra function latch load compared to the
initialization sequence method.
1.7.5 DEVICE PROGRAMMING
When
programming
LMX2326, first determine the frequencies and mode of op-
eration desired. Data register is programmed with a 21-bit
data stream shifted into the R counter, N counter, or the F
latch. The Functional Description section shows the bits for
the R counter, and the corresponding information for the N
counter. The FL
programming information is given in the
FUNCTION AND INITIALIZATION LATCHES section. Typi-
cal numbers for a GSM application example are given. In the
example, the RF output is locking at 950 MHz (f
) with a
200 kHz channel spacing (f
comparison
). The crystal oscillator
reference input is 10 MHz (f
is 32. An example of both methods of FastLock will be
shown.
The last two bits (control bits C1 and C2) of each bit stream
identify which counter or FL
o
mode will be programmed. For
example, to program the R counter, C1 and C2 will be 0,0.
Immediately proceeding these two bits is the N, R, or F bits
providing the divide ratios and FastLock mode information.
the
LMX2306,
LMX2316,
and
Control Bits
C1
0
1
0
1
DATA Location
C2
0
0
1
1
R Counter
N Counter
Function Latch
Initialization
For example, to load the N counter, the last two bits C1 and
C2 must be 10.
Once the control bits have been determined, the frequency
information must be determined. To begin, determine the N
and R counter values as follows:
N = f
vco
/f
comparison
and
R = f
osc
/f
comparison
For this example R and N are determined as follows:
R = 10 MHz/200 kHz = 50
and
N = 950 MHz/200 kHz = 4750
L
www.national.com
15
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| LMX2331U | |
| LMX2306LBX | FREQUENCY SYNTHESIZER|BICMOS|LLCC|16PIN|PLASTIC |
| LMX2316LBX | FREQUENCY SYNTHESIZER|BICMOS|LLCC|16PIN|PLASTIC |
| LMX2324A | |
| LMX2324ASLBX | FREQUENCY SYNTHESIZER|BICMOS|LLCC|16PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMX2331LTMX/NOPB | 功能描述:IC FREQ SYNTH DUAL 20-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:PLLatinum™ 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| LMX2331U | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:PLLatinum Ultra Low Power Dual Frequency Synthesizer for RF Personal Communications |
| LMX2331USLBX | 功能描述:IC FREQ SYNTH DUAL 24LAMINATECSP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:PLLatinum™ 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| LMX2331USLEX/NOPB | 功能描述:IC FREQ SYNTH DUAL 20LAMUCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:PLLatinum™ 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| LMX2331UTM | 功能描述:IC FREQ SYNTHESIZER DUAL 20TSSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:PLLatinum™ 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
發布緊急采購，3分鐘左右您將得到回復。