- 您現在的位置：買賣IC網 > PDF目錄358886 > LMV921M7 (NATIONAL SEMICONDUCTOR CORP) 1.8V, 1MHz, Low Power Operational Amplifiers with Rail-To-Rail Input and Output PDF資料下載
參數資料
| 型號： | LMV921M7 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 運算放大器 |
| 英文描述： | 1.8V, 1MHz, Low Power Operational Amplifiers with Rail-To-Rail Input and Output |
| 中文描述： | OP-AMP, 6000 uV OFFSET-MAX, 1 MHz BAND WIDTH, PDSO5 |
| 封裝： | SC-70, 5 PIN |
| 文件頁數： | 16/27頁 |
| 文件大?。?/td> | 736K |
| 代理商： | LMV921M7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
Application Note
(Continued)
This V
crossover point can create problems for both DC
and AC coupled signals if proper care is not taken. For large
input signals that include the V
crossover point in their dy-
namic range, this will cause distortion in the output signal.
One way to avoid such distortion is to keep the signal away
from the crossover. For example, in a unity gain buffer con-
figuration and with V
= 5V, a 5V peak-to-peak signal will
contain input-crossover distortion while a 3V peak-to-peak
signal centered at 1.5V will not contain input-crossover dis-
tortion as it avoids the crossover point. Another way to avoid
large signal distortion is to use a gain of 1 circuit which
avoids any voltage excursions at the input terminals of the
amplifier. In that circuit, the common mode DC voltage can
be set at a level away from the V
OS
cross-over point.
For small signals, this transition in V
shows up as a V
dependent spurious signal in series with the input signal and
can effectively degrade small signal parameters such as
gain and common mode rejection ratio. To resolve this prob-
lem, the small signal should be placed such that it avoids the
V
OS
crossover point.
In addition to the rail-to-rail performance, the output stage
can provide enough output current to drive 600
loads. Be-
cause of the high current capability, care should be taken not
to exceed the 150C maximum junction temperature specifi-
cation.
5.0 Power-Supply Considerations
The LMV921/LMV922/LMV924 are ideally suited for use with
most battery-powered systems. The LMV921/LMV922/
LMV924 operate from a single +1.8V to +5.0V supply and
consumes about 145μA of supply current per Amplifier. A
high power supply rejection ratio of 78dB allows the amplifier
to be powered directly off a decaying battery voltage extend-
ing battery life.
Table 1 lists a variety of typical battery types. Batteries have
different voltage ratings; operating voltage is the battery volt-
age under nominal load. End-of-Life voltage is defined as the
voltage at which 100% of the usable power of the battery is
consumed. Table 1 also shows the typical operating time of
the LMV921.
6.0 Distortion
The two main contributors of distortion in LMV921/LMV922/
LMV924 family is:
1. Output crossover distortion occurs as the output transi-
tions from sourcing current to sinking current.
2. Input crossover distortion occurs as the input switches
from NPN to PNP transistor at the input stage.
To decrease crossover distortion:
1. Increase the load resistance. This lowers the output cross-
over distortion but has no effect on the input crossover dis-
tortion.
2. Operate from a single supply with the output always
sourcing current.
3. Limit the input voltage swing for large signals between
ground and one volt below the positive supply.
4. Operate in inverting configuration to eliminate common
mode induced distortion.
5.Avoid small input signal around the input crossover region.
The discontinuity in the offset voltage will effect the gain,
CMRR and PSRR.
TABLE 1. LMV921 Characteristics with Typical Battery Systems.
Battery Type
Operating
Voltage (V)
End-of-Life
Voltage (V)
Capacity AA
Size (mA -
h)
1000
1000
375
500
LMV921
Operating
time (Hours)
6802
6802
2551
3401
Alkaline
Lithium
Ni - Cad
NMH
1.5
2.7
1.2
1.2
0.9
2.0
0.9
1.0
L
www.national.com
16
相關PDF資料 |
PDF描述 |
|---|---|
| LMV921M7X | 1.8V, 1MHz, Low Power Operational Amplifiers with Rail-To-Rail Input and Output |
| LMV921_QUAL | 1.8V RR I/O Op Amp |
| LMV981IDBVT | 1.8-V OPERATIONAL AMPLIFIERS WITH RAIL-TO-RAIL AND OUTPUT AND SHUTDOWN |
| LMV982 | 1.8V, RRIO Operational Amplifiers with Shutdown |
| LMV982MM | 1.8V, RRIO Operational Amplifiers with Shutdown |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMV921M7X | 功能描述:IC OP AMP LO PWR RRIO SC-70-5 RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| LMV922 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:1.8V, 1MHz, Low Power Operational Amplifiers with Rail-To-Rail Input and Output |
| LMV922A WAF | 制造商:Texas Instruments 功能描述: |
| LMV922M | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:OC White Company 功能描述:OP Amp Dual GP R-R I/O 5V 8-Pin SOIC N Rail |
| LMV922MM | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。