- 您現在的位置：買賣IC網 > PDF目錄361042 > LMV115 (National Semiconductor Corporation) GSM Baseband 30MHz 2.8V Oscillator Buffer PDF資料下載
參數資料
| 型號： | LMV115 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | GSM Baseband 30MHz 2.8V Oscillator Buffer |
| 中文描述： | GSM基帶30MHz的2.8V的振蕩器緩沖 |
| 文件頁數： | 11/13頁 |
| 文件大小： | 475K |
| 代理商： | LMV115 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁
Application Section
(Continued)
In
Figure 3
the input signal is swept between both supply
rails (0V - 2.8V). The linear part of the plot ‘V
vs. V
’
covers approximately the voltage range between 1.0V and
2.0V. If a difference of 50mV between output and input is
acceptable, the output range is between 1.05V and 2.15V
(see curve V
– V
). Alternatively the output voltage
swing can be determined by using
Figure 4
. In the plot ‘Gain
vs. V
’ it can be seen that the gain is flat for input voltages
from 1.15V till 2.1V. Outside this range the gain differs from
1. This will introduce distortion of the output signal.
Another point is the DC bias voltage necessary to get the
optimum output voltage swing. As discussed above, the
output voltage swing can be 1V
, but if the two internal bias
resistors are used, the DC bias will be 1.4V, which is half of
the supply voltage of 2.8V. In this situation the output swing
will exceed the lower limit of 1.15V, so it is necessary to
introduce a small DC offset of 200mV to make use of the full
output swing range of the output stage.
DRIVING RESISTIVE AND CAPACITIVE LOADS
The maximum output current of the LMV115 is about 200μA
which means the output can drive a maximum load of 1V/
200μA = 5k
. Using lower load resistances will exceed the
maximum linear output current. The LMV115 can drive a
small capacitive load, but make sure that every capacitor
directly connected to the output becomes part of the loop of
the buffer and will reduce the gain/phase margin, increasing
the instability at higher capacitive values. This will lead to
peaking in the frequency response and in extreme situations
oscillations can occur. A good practice when driving larger
capacitive loads is to include a series resistor to the load
capacitor. A to D converters present complex and varying
capacitive loads to the buffer. The best value for this isolation
resistance is often found by experimentation.
SHUTDOWN MODE
LMV115 offers a shutdown function that can be used to
disable the device and to optimize current consumption.
Switching between the normal mode and the shutdown
mode requires connecting the shutdown pin either to the
negative or the positive supply rail. If directly connected to
one of the supply rails, the part is guaranteed in the correct
mode. But if the shutdown pin is driven by other output
stages, there is a voltage range in which the installed mode
is not certainly set and it is recommended not to drive the
shutdown pin in this voltage range. As can be seen in
Figure
5
this hysteresis varies from 1V to 1.6V. Below 1V the
LMV115 is securely ‘ON’ and above 1.6V securely ‘OFF’
while using a supply voltage of 2.8V.
PRINTED CIRCUIT BOARD LAYOUT AND COMPONENT
VALUES SELECTION
For a good high frequency design both the active parts and
the passive ones should be suitable for the purpose they are
used for. Amplifying high frequencies is possible with stan-
dard through-hole components, but for frequencies above
several hundreds of MHz the best choice is using surface
mount devices. Nowadays designs are often assembled with
surface mount devices for the aspect of minimizing space,
but this also greatly improves the performance of designs,
handling high frequencies. Another important issue is the
PCB, which is no longer a simple carrier for all the parts and
a medium to interconnect them. The board becomes a real
20075133
FIGURE 3. V
OUT
– V
IN
20075134
FIGURE 4. Gain
20075135
FIGURE 5. Hysteresis
L
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| LMV115MG | TRANS PNP 50VCEO 2A TO-126 |
| LMV115MGX | TRANS PNP HF 60VCEO 2A TO-126 |
| LMV228TLX | RF Power Detector for CDMA and WCDMA |
| LMV225SD | RF Power Detector for CDMA and WCDMA |
| LMV225SDX | RF Power Detector for CDMA and WCDMA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMV115 WAF | 制造商:Texas Instruments 功能描述: |
| LMV115A E WAF | 制造商:Texas Instruments 功能描述: |
| LMV115MG | 制造商:Texas Instruments 功能描述:BUFFER SINGLE CLOCK MSOP10 115 |
| LMV115MG/NOPB | 功能描述:IC BUFFER OSC GSM 30MHZ SC70-6 RoHS:是 類別:RF/IF 和 RFID >> RF 其它 IC 和模塊 系列:- 標準包裝:100 系列:* |
| LMV115MGX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:GSM Baseband 30MHz 2.8V Oscillator Buffer |
發布緊急采購，3分鐘左右您將得到回復。