- 您現在的位置：買賣IC網 > PDF目錄3622 > LMH6642MF/NOPB (National Semiconductor)IC OPAMP LP 3V 75MA RR SOT23-5 PDF資料下載
參數資料
| 型號： | LMH6642MF/NOPB |
| 廠商： | National Semiconductor |
| 文件頁數： | 10/33頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP LP 3V 75MA RR SOT23-5 |
| 產品培訓模塊： | High Speed Amplifiers for Video Applications - Part 1 High Speed Amplifiers for Video Applications - Part 2 High Speed Amplifiers for Video Applications - Part 3 |
| 標準包裝： | 1 |
| 系列： | PowerWise® |
| 放大器類型： | 電壓反饋 |
| 電路數： | 1 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 135 V/µs |
| -3db帶寬： | 130MHz |
| 電流 - 輸入偏壓： | 1.6µA |
| 電壓 - 輸入偏移： | 1000µV |
| 電流 - 電源： | 2.7mA |
| 電流 - 輸出 / 通道： | 75mA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 12.8 V，±1.35 V ~ 6.4 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SC-74A，SOT-753 |
| 供應商設備封裝： | SOT-23-5 |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 1270 (CN2011-ZH PDF) |
| 配用： | LMH730227-ND - BOARD EVALUATION FOR SOIC PKG LMH730165-ND - BOARD EVALUATION LMH730216-ND - BOARD EVAL HS MONO AMP SOT23 |
| 其它名稱： | LMH6642MFDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
IN+
IN-
R
V-
V+
V-
VIN (1 V/DIV)
VOUT (2 V/DIV)
VS=±5V, VIN=5VPP
AV=+5, RF=RL=2k
2 V/DIV
100 ns/DIV
SNOS966P – MAY 2001 – REVISED MARCH 2013
Figure 61. Overload Recovery Waveform
INPUT AND OUTPUT TOPOLOGY
All input / output pins are protected against excessive voltages by ESD diodes connected to V+ and V-rails (see
Figure 62). These diodes start conducting when the input / output pin voltage approaches 1Vbe beyond V
+ or V-
to protect against over voltage. These diodes are normally reverse biased. Further protection of the inputs is
provided by the two resistors (R in Figure 62), in conjunction with the string of anti-parallel diodes connected
between both bases of the input stage. The combination of these resistors and diodes reduces excessive
differential input voltages approaching 2Vbe. The most common situation when this occurs is when the device is
used as a comparator (or with little or no feedback) and the device inputs no longer follow each other. In such a
case, the diodes may conduct. As a consequence, input current increases and the differential input voltage is
clamped. It is important to make sure that the subsequent current flow through the device input pins does not
violate the Absolute Maximum Ratings of the device. To limit the current through this protection circuit, extra
series resistors can be placed. Together with the built-in series resistors of several hundred ohms, these external
resistors can limit the input current to a safe number (i.e. < 10mA). Be aware that these input series resistors
may impact the switching speed of the device and could slow down the device.
Figure 62. Input Equivalent Circuit
SINGLE SUPPLY, LOW POWER PHOTODIODE AMPLIFIER
The circuit shown in Figure 63 is used to amplify the current from a photodiode into a voltage output. In this
circuit, the emphasis is on achieving high bandwidth and the transimpedance gain setting is kept relatively low.
Because of its high slew rate limit and high speed, the LMH664X family lends itself well to such an application.
This circuit achieves approximately 1V/mA of transimpedance gain and capable of handling up to 1mApp from the
photodiode. Q1, in a common base configuration, isolates the high capacitance of the photodiode (Cd) from the
Op Amp input in order to maximize speed. Input is AC coupled through C1 to ease biasing and allow single
supply operation. With 5V single supply, the device input/output is shifted to near half supply using a voltage
divider from VCC. Note that Q1 collector does not have any voltage swing and the Miller effect is minimized. D1,
tied to Q1 base, is for temperature compensation of Q1’s bias point. Q1 collector current was set to be large
enough to handle the peak-to-peak photodiode excitation and not too large to shift the U1 output too far from
mid-supply.
18
Copyright 2001–2013, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| GBC19SABN-M30 | CONN HEADER 19PS .100 SINGLE SMD |
| 1-640384-9 | CONN HEADER 19POS VERT .156 TIN |
| 1206SFH120F/24-2 | FUSE 12A 24V FAST SMD 1206 |
| 1206SFH200F/24-2 | FUSE 20A 24V FAST SMD 1206 |
| 5-87543-6 | 12 MODII HDR DRST UNSHRD .100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMH6642MFX | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| LMH6642MFX/NOPB | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| LMH6642MFXEP | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Enhanced Plastic Low Power, 130MHz, 75mA Rail-to-Rail Output Amplifiers |
| LMH6642Q | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low Power, 130MHz, 75mA Rail-to-Rail Output Amplifiers |
| LMH6642QMF | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low Power, 130MHz, 75mA Rail-to-Rail Output Amplifiers |
發布緊急采購，3分鐘左右您將得到回復。