- 您現在的位置：買賣IC網 > PDF目錄358877 > LM93CIMTX (NATIONAL SEMICONDUCTOR CORP) LJT 6C 6#12 PIN PLUG PDF資料下載
參數資料
| 型號： | LM93CIMTX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 電源管理 |
| 英文描述： | LJT 6C 6#12 PIN PLUG |
| 中文描述： | 16-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO56 |
| 封裝： | MO-153EE, TSSOP-56 |
| 文件頁數： | 16/92頁 |
| 文件大?。?/td> | 654K |
| 代理商： | LM93CIMTX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁
12.0 Functional Description
(Continued)
mented to a max count for an above temperature trip and
decremented to zero when below the trip temperature set-
ting, to remove the trip.
The minimum time for PROCHOT assertion is time depen-
dant on the FSB frequency. The minimum time that the
processor asserts PROCHOT is estimated to be 187 μs.
12.10 PROCHOT MONITORING
PROCHOT monitoring applies to both the P1_PROCHOT
and P2_PROCHOT inputs. Both inputs are monitored in the
same fashion, but the following description discusses a
single
monitor.
(Px_PROCHOT
P1_PROCHOT and P2_PROCHOT).
PROCHOT monitoring is meant to achieve two goals. One
goal is to measure the percentage of time that PROCHOT is
asserted over a programmable time period. The result of this
measurement can be read from an 8-bit register where one
LSB equals 1/256th of the PROCHOT Time Interval (0.39%).
The second goal is to have a status register that indicates,
as a coarse percentage, the amount of time a processor has
been throttled. This second goal is required in order to
communicate information over the NIC using ASF, i.e. status
can be sent, not values.
To achieve the first goal, the PROCHOT input is monitored
over a period of time as defined by the PROCHOT Time
Interval Register. At the end of each time period, the 8-bit
measurement is transferred to the Current Px_PROCHOT
register. Also at the end of each measurement period, the
Current Px_PROCHOT register value is moved to the Aver-
age Px_PROCHOT register by adding the new value to the
old value and dividing the result by 2. Note that the value that
is averaged into the Average Px_PROCHOT register is not
the new measurement but rather the previous measurement.
If the SMBus writes to the Current P1_PROCHOT (or Cur-
rent P2_PROCHOT) register, the capture cycle restarts for
both
monitoring
channels
P2_PROCHOT). Also note, that a strict average of two 8-bit
values may result in Average Px_PROCHOT reflecting a
value that is one LSB lower than the Current Px_PROCHOT
in steady state.
It should be noted that the 8-bit result has a positive bias of
one half of an LSB. This is necessary because a value of 00h
represents that Px_PROCHOT was not asserted at all dur-
ing the sampling window. Any amount of throttling results in
a reading of 01h.
The following table demonstrates the mapping for the 8-bit
result:
represents
both
(P1_PROCHOT
and
8–Bit Result
0
1
2
Percentage Thottled
Exactly 0%
Between 0% and 0.39%
Between 0.39% and 0.78%
A
A
n
Between (n-1)/256 and n/256
A
A
253
254
255
Between 98.4% and 98.8%
Between 98.8% and 99.2%
Greater than 99.2%
To achieve the second goal, the LM93 has several compara-
tors that compare the measured percentage reading against
several fixed and 1 variable value. The variable value is user
programmable.
The result of these comparisons generates several error
status bits described in the following table:
Status Description
100% Throttle
Comparison Formula
PROCHOT was never
de-asserted during
monitoring interval.
193
≤
measured value and
not 100%
129
≤
measured value
<
193
65
≤
measured value
<
129
Greater than or equal to
75% and less than 100%
Greater than or equal to
50% and less than 75%
Greater than or equal to
25% and less than 50%
Greater than or equal to
12.5% and less than 25%
Greater than 0% and less
than 12.5%
Greater than 0%
Greater than user limit
33
≤
measured value
<
65
0
<
measured value
<
33
0
<
measured value
user limit
<
measured
value
These status bits are reflected in the PROCHOT Error Sta-
tus
Registers.
Each
of
P2_PROCHOT inputs is monitored independently, and each
has its own set of status registers.
In S3 and S4/5 sleep states, the PROCHOT Monitoring
function does not run. The Current Px_PROCHOT registers
are reset to 00h and the Average Px_PROCHOT registers
hold their current state. Once the sleep state changes back
to S0, the monitoring function is restarted. After the first
PROCHOT measurement has been made, the measure-
ment is written directly into the Current and Average Px-
_PROCHOT registers without performing any averaging. Av-
eraging returns to normal on the second measurement.
the
P1_PROCHOT
and
12.11 PROCHOT OUTPUT CONTROL
In some cases, it is necessary for the LM93 to drive the
Px_PROCHOT outputs low. There are several conditions
that cause this to happen.
The LM93 can be told to logically short the two PROCHOT
inputs together. When this is done, the LM93 monitors each
of the Px_PROCHOT inputs. If any external device asserts
one of the PROCHOT signals, the LM93 responds by assert-
ing the other PROCHOT signal until the first PROCHOT
signal is de-asserted. This feature should never be enabled
if the PROCHOT signals are already being shorted by an-
other means.
Whenever one of the VRDx_HOT inputs is asserted, the
corresponding Px_PROCHOT pins are asserted by the
LM93. The response time is less than 10 μs. When the
VRDx_HOT input is de-asserted, the Px_PROCHOT pin is
no longer asserted by the LM93. If the LM93 is configured to
short the PROCHOT signals together, it always asserts them
together whenever either of the VRDx_HOT inputs is as-
serted.
Software can manually program the LM93 to drive a PWM
type signal onto P1_PROCHOT or P2_PROCHOT. This is
done via the PROCHOT Override register. See the descrip-
tion of this register for more details. Once again, if the LM93
L
www.national.com
16
相關PDF資料 |
PDF描述 |
|---|---|
| LM95010 | Digital Temperature Sensor with SensorPath⑩ Bus in MSOP8 Package |
| LM95010CIMMX | Digital Temperature Sensor with SensorPath⑩ Bus in MSOP8 Package |
| LM95010CIMM | Digital Temperature Sensor with SensorPath⑩ Bus in MSOP8 Package |
| LM95071 | SPI/MICROWIRE⑩ 13-Bit Plus Sign Temperature Sensor |
| LM95071CIMFX | SPI/MICROWIRE⑩ 13-Bit Plus Sign Temperature Sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM93CIMTX/NOPB | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LM94 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:TruTherTM Hardware Monitor with PI Loop Fan Control for Server Management |
| LM94021 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Multi-Gain Analog Temperature Sensor |
| LM94021BIMG | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM94021BIMG/NOPB | 功能描述:板上安裝溫度傳感器 Lo Volt Temp Sensor W/ Selectable Gain RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。