- 您現在的位置：買賣IC網 > PDF目錄361035 > LM9040 (National Semiconductor Corporation) Dual Lambda Sensor Interface Amplifier PDF資料下載
參數資料
| 型號： | LM9040 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Dual Lambda Sensor Interface Amplifier |
| 中文描述： | 雙氧傳感器接口放大器 |
| 文件頁數： | 8/10頁 |
| 文件大?。?/td> | 178K |
| 代理商： | LM9040 |
Open Input Pins Defaults
(Continued)
In the cases where both the inverting and non-inverting pins
are open, the non-inverting condition (i.e.: voltage divider
across the output) will be the dominant condition.
Any common mode signal seen by inverting input pin should
not be allowed to exceed the Common Mode voltage range.
Exceeding the positive Common Mode voltage limit could
cause the inverting input pin voltage comparator to act as if
the inverting input pin is open. Since the comparator circuit
is not part of the switched capacitor network there is no
frequency limitation on the signal to the comparator. Any
transient on the inverting input pin which goes above the
comparator threshold will immediately cause the output to
switch to the open sensor mode. The output will return to
normal operation when the voltage on the inverting input
falls below the comparator threshold.
Supply Bypassing
For best performance the LM9040 requires a V
CC
supply
which is stable and noise free. The same 5V V
REF
supply
used for the A/D converter is the recommended V
CC
sup-
ply. During operation the device will generate current spikes
coincident with the clock edges. Inadequate bypassing will
cause excessive clock noise on the outputs, as well as
noise on the V
CC
line. The LM9040 V
CC
pin should be by-
passed with a minimum 0.1
m
F capacitor to the Signal
Ground pin, and should be located as close to the device as
possible. Some applications may require an additional
4.7
m
F tantalum capacitor, especially if there are several
other switched capacitor devices running off the same 5V
supply line. The Signal and Digital Ground pins should be
tied together as close to the device as possible.
TL/H/12372–21
FIGURE 11. Typical Application
8
相關PDF資料 |
PDF描述 |
|---|---|
| LM9040M | Dual Lambda Sensor Interface Amplifier |
| LM9044 | LM9044 Lambda Sensor Interface Amplifier |
| LM9044V | LM9044 Lambda Sensor Interface Amplifier |
| LM9061 | Power MOSFET Driver with Lossless Protection |
| LM9061N | Power MOSFET Driver with Lossless Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM9040M | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Dual Lambda Sensor Interface Amplifier |
| LM9040M/NOPB | 功能描述:IC SENSOR DUAL INTER AMP 14-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| LM9040MX | 功能描述:IC AMP DUAL SENSR INTERFC 14SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| LM9040MX/NOPB | 制造商:Texas Instruments 功能描述:Lambda Sensor Interface Amplifier 14-Pin SOIC W T/R |
| LM9044 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9044 Lambda Sensor Interface Amplifier |
發布緊急采購，3分鐘左右您將得到回復。