- 您現在的位置：買賣IC網 > PDF目錄385489 > LM8500IVA9 (National Semiconductor Corporation) Four Wire Resistive Touchscreen Controller with Brownout PDF資料下載
參數資料
| 型號： | LM8500IVA9 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Four Wire Resistive Touchscreen Controller with Brownout |
| 中文描述： | 四線電阻式觸摸屏控制器掉電 |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 319K |
| 代理商： | LM8500IVA9 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
4.0 Functional Description
(Continued)
WD_Out
— Watch dog output. For correct operation, this
pin should be connected to the RESET pin.
OSC_OUT
— Clock oscillator output pin.
OSC_IN
— Clock oscillator input pin
GND
— Digital Ground
AGND
— Analog ground
DV
CC
— Digital power supply.
AV
— Analog power supply. For best performance, this
pin should be connected to a filter.
Users of the LLP package are cautioned to be aware that the
central metal area and the pin 1 index mark on the bottom of
the package may be connected to GND. See figure below:
4.3 USART Framing Format
The device communicates with the touch screen driver using
the UART set at a baud rate of 38400, 8, n, 1.
All communication from the host software and the controller
consists of a command byte and occasionally data byte(s). If
data byte(s) follow a command byte, it must be sent directly
after the command byte. If the device is in the power save
mode, a delay must be inserted between the wake up com-
mand and the command byte. Refer to the Power Save
mode section for more details. For every command byte sent
to the controller, an acknowledge byte is sent back and
sometimes data byte(s).
A command byte is distinguished by having the 7th bit of the
command byte set (1). If any data byte(s) is to follow, the 7th
bit of the data byte is reset (0).
Data packets sent to the host software can be either four or
five bytes in length. If the pressure measurement is enabled,
five bytes are sent. If the pressure measurement is not
enabled, four bytes are sent.
The first byte of each data packet is a header byte. This
header byte is used to synchronize and differentiate between
four or five byte packages. If a four byte data package is
sent, the 4th bit of the header byte is reset (0). If a five byte
data package is sent, the 4th bit of the header byte is set (1).
The 6th bit of the second byte of the data packet is used to
indicate the touch state. If the bit is set (1), then a touchdown
or continuous touch is detected. If the bit is reset (0), then a
liftoff is detected.
4.3.1. Data packet format table
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
1
0
0
L
0
S
X
2
X
1
0
X
9
X
8
X
7
0
Y
9
Y
8
Y
7
0
Z
6
Z
5
Z
4
Byte 1
Byte 2
Byte 3
Byte 4
Byte 5
0
X
0
X
6
Y
6
Z
3
0
Y
2
X
5
Y
5
Z
2
0
Y
1
X
4
Y
4
Z
1
0
Y
0
X
3
Y
3
Z
0
L - Package length. (0 = 4 bytes, 1 = 5 bytes)
S - Touch state (0 = liftoff, 1 = touchdown or continuous
touch)
X
X
- X position (10 bit value)
Y
Y
- Y position (10 bit value)
Z
- Z positon (7 bit value), this byte is only transmitted if the
pressure measurement is enabled
4.3.2 Command Bytes
PC
Command
Read
clock-speed
(3,33MHz,
10MHz)
Read
parameters
PC
Byte 1
$B0
PC
Byte 2
TSC
Byte 1
$CA
TSC
Byte 2
$00, $01
$B1
$CA
4.3.3
Advanced
Command
Bytes
Descriptions
4.3.3
Advanced
Command
Bytes
Descriptions
$00, $02,
$05, $0D
Read
software
version
number
$B2
$C7
Read # of
calibration
points
Read stored
calibration
points
$B3
$CA
$B4
$CA
4.3.3
Advanced
Command
Bytes
Descriptions
$
00-$3F
Set focus
value (# of
pixels on
touch panel)
Set # of
samples per
coordinate (1,
2, 4, 8, 16,
32)
Set
communication
mode
(stream,
touchdown,
liftoff)
$B8
$0-$3F
$CA
$BA
$01, $02,
$04, $08,
$10, $20
$CA
$01, $02,
$04, $08,
$10, $20
$BB
$01, $02,
$04
$CA
$01, $02,
$04
20037216
FIGURE 1. LLP Package Bottom View
L
www.national.com
9
相關PDF資料 |
PDF描述 |
|---|---|
| LM85 | Hardware Monitor with Integrated Fan Control |
| LM86 | 【0.75∑C Accurate, Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| LM86CIM | 【0.75∑C Accurate, Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| LM86CIMM | 【0.75∑C Accurate, Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| LM86CIMMX | 【0.75∑C Accurate, Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM8500-REF-01 | 功能描述:顯示開發工具 LM8500 DEV KIT RoHS:否 制造商:4D Systems 產品:4Display Shields 工具用于評估:?OLED-160-G1, ?OLED-160-G2 接口類型:Serial 工作電源電壓:5 V |
| LM8502 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Intelligent Lighting Management Unit That Fuses a 1.2A Dual High-Side Flash LED Driver with a 10-Output Low-Side LED Driver |
| LM8502TME | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Intelligent Lighting Management Unit That Fuses a 1.2A Dual High-Side Flash LED Driver with a 10-Output Low-Side LED Driver |
| LM8502TME/NOPB | 功能描述:LED照明驅動器 RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| LM8502TMX | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Intelligent Lighting Management Unit That Fuses a 1.2A Dual High-Side Flash LED Driver with a 10-Output Low-Side LED Driver |
發布緊急采購，3分鐘左右您將得到回復。