- 您現在的位置：買賣IC網 > PDF目錄385489 > LM8500IMT9 (NATIONAL SEMICONDUCTOR CORP) Four Wire Resistive Touchscreen Controller with Brownout PDF資料下載
參數資料
| 型號： | LM8500IMT9 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 消費家電 |
| 英文描述： | Four Wire Resistive Touchscreen Controller with Brownout |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO48 |
| 封裝： | TSSOP-48 |
| 文件頁數： | 17/20頁 |
| 文件大?。?/td> | 319K |
| 代理商： | LM8500IMT9 |
9.0 Calibration
(Continued)
9.1 General Calibration Procedures
Calibration is invoked by sending a command byte of $BD
followed by a command byte to the device. The command
byte is broken into two parts: the high nibble states the
number of calibration points to performs and the lower nibble
states the active calibration point. For example, to do the first
calibration point for the two point calibration, the command
bytes of $BD and $11 are sent to the device. The device then
echos $BD and $11 back to the TS driver and waits for a
touch on the panel. When a touch is detected, the device
checks to see if the point is within the specified parameters
if the calibration point checking is enabled. If the calibration
point checking is disabled, the device will send a
$
C8 for OK
byte to the TS driver regardless of where the touch was
detected. This calibration point checking can be enabled or
disabled by sending a command byte of $A5 to the device.
When all the calibration points are done, the device will do a
self-test and send a command of $CB for OK or a command
of $CC for failed. If a $CC is received, the TS driver should
issue a warning stating the calibration was not done properly
and redo the calibration procedures. The flowchart for the
calibration procedures is shown in
Figure 8
.
20037210
FIGURE 8. Calibration Procedures with Coordinates Checking Enabled
L
www.national.com
17
相關PDF資料 |
PDF描述 |
|---|---|
| LM8500IVA9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM85 | Hardware Monitor with Integrated Fan Control |
| LM86 | 【0.75∑C Accurate, Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| LM86CIM | 【0.75∑C Accurate, Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| LM86CIMM | 【0.75∑C Accurate, Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM8500IMT9B | 功能描述:觸摸屏轉換器和控制器 RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| LM8500IMT9B/NOPB | 功能描述:觸摸屏轉換器和控制器 RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| LM8500IVA9 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Four Wire Resistive Touchscreen Controller with Brownout |
| LM8500-REF-01 | 功能描述:顯示開發工具 LM8500 DEV KIT RoHS:否 制造商:4D Systems 產品:4Display Shields 工具用于評估:?OLED-160-G1, ?OLED-160-G2 接口類型:Serial 工作電源電壓:5 V |
| LM8502 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Intelligent Lighting Management Unit That Fuses a 1.2A Dual High-Side Flash LED Driver with a 10-Output Low-Side LED Driver |
發布緊急采購，3分鐘左右您將得到回復。