- 您現在的位置：買賣IC網 > PDF目錄361034 > LM8300ILQ9 (National Semiconductor Corporation) Four Wire Resistive Touchscreen Controller with Brownout PDF資料下載
參數資料
| 型號： | LM8300ILQ9 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Four Wire Resistive Touchscreen Controller with Brownout |
| 中文描述： | 四線電阻式觸摸屏控制器掉電 |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 327K |
| 代理商： | LM8300ILQ9 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
9.0 Functional Description
(Continued)
LED
— Optional LED output. When the controller is oper-
ating in normal (non power save) mode, a low is output to the
pin. When the controller is in power save mode, a high is
output to the pin.
RESET
— Reset pin. When pulled low, a manual reset is
executed. For normal operation, this pin must be pulled high.
Under no circumstances should the pin be left floating.
UART_TX
— UART transmit pin. The signal is inverted for
use with standard RS-232 drivers.
UART_RX
— UART receive pin. The signal is inverted for
use with standard RS-232 drivers.
DTR
— Data Terminal Ready signal for the UART. If a high
level is detected on the pin, this signals that the UART is not
ready. If a low level is detected on the pin, this signals that
the UART is ready.
WD_Out
— Watch dog output. For correct operation, this
pin should be connected to the RESET pin.
OSC_OUT
— Clock oscillator output pin.
OSC_IN
— Clock oscillator input pin
GND
— Digital Ground
AGND
— Analog ground
DV
CC
— Digital power supply.
AV
CC
— Analog power supply. For best performance, this
pin should be connected to a filter.
Users of the LLP package are cautioned to be aware that the
central metal area and the pin 1 index mark on the bottom of
the package may be connected to GND. See figure below:
9.3 USART FRAMING FORMAT
The device communicates with the touch screen driver using
the UART set at a baud rate of 38400, 8, n, 1.
All communication from the host software and the controller
consists of a command byte and occasionally data byte(s). If
data byte(s) follow a command byte, it must be sent directly
after the command byte. If the device is in the power save
mode, a delay must be inserted between the wake up com-
mand and the command byte. Refer to the Power Save
mode section for more details. For every command byte sent
to the controller, an acknowledge byte is sent back and
sometimes data byte(s).
A command byte is distinguished by having the 7th bit of the
command byte set (1). If any data byte(s) is to follow, the 7th
bit of the data byte is reset (0).
Data packets sent to the host software can be either four or
five bytes in length. If the pressure measurement is enabled,
five bytes are sent. If the pressure measurement is not
enabled, four bytes are sent.
The first byte of each data packet is a header byte. This
header byte is used to synchronize and differentiate between
four or five byte packages. If a four byte data package is
sent, the 4th bit of the header byte is reset (0). If a five byte
data package is sent, the 4th bit of the header byte is set (1).
The 6th bit of the second byte of the data packet is used to
indicate the touch state. If the bit is set (1), then a touchdown
or continuous touch is detected. If the bit is reset (0), then a
liftoff is detected.
9.3.1 Data packet format table
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
1
0
0
L
0
S
X
2
X
1
0
X
9
X
8
X
7
0
Y
9
Y
8
Y
7
0
Z
6
Z
5
Z
4
Byte 1
Byte 2
Byte 3
Byte 4
Byte 5
0
X
0
X
6
Y
6
Z
3
0
Y
2
X
5
Y
5
Z
2
0
Y
1
X
4
Y
4
Z
1
0
Y
0
X
3
Y
3
Z
0
L - Package length. (0 = 4 bytes, 1 = 5 bytes)
S - Touch state (0 = liftoff, 1 = touchdown or continuous
touch)
X
X
- X position (10 bit value)
Y
Y
- Y position (10 bit value)
Z
- Z positon (7 bit value), this byte is only transmitted if the
pressure measurement is enabled
9.3.2 Command Bytes
PC
Command
PC
Byte
1
$B0
PC
Byte 2
TSC
Byte 1
TSC
Byte 2
Read
clock-speed
(3,33MHz,
10MHz)
Read
parameters
$CA
$00, $01
$B1
$CA
Section
9.3.3
Advanced
Command
Bytes
Descriptions
Section
9.3.3
Advanced
Command
Bytes
Descriptions
$00, $02,
$05, $0D
Read
software
version
number
$B2
$C7
Read # of
calibration
points
$B3
$CA
20037216
FIGURE 1. LLP Package Bottom View
L
www.national.com
9
相關PDF資料 |
PDF描述 |
|---|---|
| LM8300IMT9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8300IVA9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8300 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8300HLQ9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8300HMT9 | Four Wire Resistive Touchscreen Controller with Brownout |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM8300IMT9 | 功能描述:IC TOUCHSCREEN CONTROLLR 48TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| LM8300IMT9/NOPB | 制造商:Texas Instruments 功能描述:Four Wire Resistive Touchscreen Controller With Brownout 48-Pin TSSOP |
| LM8300IMT9B | 功能描述:觸摸屏轉換器和控制器 RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| LM8300IMT9B/63 | 功能描述:觸摸屏轉換器和控制器 RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| LM8300IMT9B/63SN | 功能描述:觸摸屏轉換器和控制器 RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
發布緊急采購，3分鐘左右您將得到回復。