參數資料
型號： LM80CIMTX-5
英文描述： Single-Ended Data Acquisition System
中文描述： 單端數據采集系統
文件頁數： 13/29頁
文件大?。?/td> 409K
代理商： LM80CIMTX-5
Functional Description
(Continued)
A typical application, such as is shown in Figure 6 might
select the input voltage divider to provide 1.9V at the analog
inputs of the LM80. This is sufficiently high for good resolu-
tion of the voltage, yet leaves headroom for upward excur-
sions from the supply of about 25%. To simplify the process
of resistor selection, set the value of R2 first. Select a value
for R2 or R4 between 10 k
and 100 k
This is low enough
to avoid errors due to input leakage currents yet high enough
to both protect the inputs under overdrive conditions as well
as minimize loading of the source. Then select R1 or R3 to
provide a 1.9V input as show in Figure 6
For positive input voltages the equation for calculating R1 is
as follows:
R1 = [ (V
S
V
IN
) / V
IN
] R2
For negative input voltages the equation for Calculating R3
is as follows:
R3 = [ (V
S
V
IN
) / (V
IN
5V)] R4
The analog inputs have internal diodes that clamp inputs
exceeding the power supply and ground. Exceeding any
analog input has no detrimental effect on other channels.
The input diodes will also clamp voltages appearing at the
inputs of an un-powered LM80. External resistors should be
included to limit input currents to the values given in the
ABSOLUTE MAXIMUM RATINGS for Input Current At Any
Pin. Inputs with the attenuator networks will usually meet
these requirements. If it is possible for inputs without attenu-
ators to be turned on while LM80 is powered off, additional
resistors of about 10 k
should be added in series with the
inputs to limit the input current.
Voltage
Measure-
ments
(V
S
)
+2.5V
+3.3V
+5.0V
+12V
12V
5V
R1 or
R3
R2 or
R4
Voltage
at
Analog Inputs
( ADC code 190)
+1.9V
+1.9V
+1.9V
+1.9V
+1.9V
+1.9V
23.7 k
22.1 k
24 k
160 k
160 k
36 k
75 k
30 k
14.7 k
30.1 k
35.7 k
16.2 k
5.0 LAYOUT AND GROUNDING
Analog inputs will provide best accuracy when referred to the
AGND pin or a supply with low noise. A separate,
low-impedance ground plane for analog ground, which pro-
vides a ground point for the voltage dividers and analog
components, will provide best performance but is not man-
datory. Analog components such as voltage dividers should
be located physically as close as possible to the LM80.
The power supply bypass, the parallel combination of 10 μF
(electrolytic or tantalum) and 0.1 μF (ceramic) bypass ca-
pacitors connected between pin 9 and ground, should also
be located as close as possible to the LM80.
DS100040-11
FIGURE 6. Input Examples. Resistor values shown in
table provide approximately 1.9V at the analog inputs.
L
www.national.com
13
相關PDF資料
PDF描述
LM8162
LM8164
LM8165
LM81CIMT-3 DATA ACQ SYSTEM|6-CHANNEL|8-BIT|TSSOP|24PIN|PLASTIC
LM81BIMT-3 DATA ACQ SYSTEM|6-CHANNEL|8-BIT|TSSOP|24PIN|PLASTIC
相關代理商/技術參數
參數描述
LM80CIMTX-5/NOPB 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
LM80CIMTX-52 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor
LM80EVAL 功能描述:EVALUATION BOARD FOR LM80 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:PowerWise® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板
LM81 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor
LM8-1 制造商:Banner Engineering 功能描述:Logic Module; Delayed One-Shot; ,Ranges For Banner Multi-Beam Sensor Blocks 制造商:Banner Engineering 功能描述:3-And 4-Wire Logic Modules
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*