- 您現在的位置：買賣IC網 > PDF目錄361032 > LM70CIMM-5 (NATIONAL SEMICONDUCTOR CORP) SPI/MICROWIRE⑩ 10-Bit plus Sign Digital Temperature Sensor PDF資料下載
參數資料
| 型號： | LM70CIMM-5 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | SPI/MICROWIRE⑩ 10-Bit plus Sign Digital Temperature Sensor |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 3.50Cel, SQUARE, SURFACE MOUNT |
| 封裝： | PLASTIC, MSOP-8 |
| 文件頁數： | 10/13頁 |
| 文件大?。?/td> | 285K |
| 代理商： | LM70CIMM-5 |
2.0 Serial Bus Timing Diagrams
3.0 Application Hints
To get the expected results when measuring temperature
with an integrated circuit temperature sensor like the LM70,
it is important to understand that the sensor measures its
own die temperature. For the LM70, the best thermal path
between the die and the outside world is through the LM70’s
pins. In the MSOP-8 package the ground pin is connected to
the back side of the LM70 die and thus has the most effect
on the die temperature. Although the other pins will also
have some effect on the LM70die temperature and therefore
should not be discounted. The LM70 will provide an accurate
measurement of the temperature of the printed circuit board
on which it is mounted, because the pins represent a good
thermal path to the die. A less efficient thermal path exists
between the plastic package and the LM70 die. If the ambi-
ent air temperature is significantly different from the printed
circuit board temperature, it will have a small effect on the
measured temperature.
In probe-type applications, the LM70 can be mounted inside
a sealed-end metal tube, and can then be dipped into a bath
or screwed into a threaded hole in a tank.As with any IC, the
LM70 and accompanying wiring and circuits must be kept in-
sulated and dry, to avoid leakage and corrosion. This is es-
pecially true if the circuit may operate at cold temperatures
where condensation can occur. Printed-circuit coatings and
varnishes such as Humiseal and epoxy paints or dips are of-
ten used to insure that moisture cannot corrode the LM70 or
its connections.
DS101223-14
a) Reading Continuous Conversion - Single Eight-Bit Frame
DS101223-15
b) Reading Continuous Conversion - Two Eight-Bit Frames
DS101223-18
c) Writing Shutdown Control
FIGURE 7. Timing Diagrams
L
www.national.com
10
相關PDF資料 |
PDF描述 |
|---|---|
| LM70CIMMX-3 | SPI/MICROWIRE⑩ 10-Bit plus Sign Digital Temperature Sensor |
| LM70CIMMX-5 | SPI/MICROWIRE⑩ 10-Bit plus Sign Digital Temperature Sensor |
| LM70 | SPI/MICROWIRE⑩ 10-Bit plus Sign Digital Temperature Sensor |
| LM70CILD-3 | SPI/MICROWIRE⑩ 10-Bit plus Sign Digital Temperature Sensor |
| LM70CILD-5 | SPI/MICROWIRE⑩ 10-Bit plus Sign Digital Temperature Sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM70CIMM-5 | 制造商:Texas Instruments 功能描述:DIG TEMP SENSOR SMD SOIC8 5.5V |
| LM70CIMM-5/NOPB | 功能描述:板上安裝溫度傳感器 SPI/10-BIT PLUS SIGN DIGITAL TEMP SENSOR RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM70CIMM-5/NOPB | 制造商:Texas Instruments 功能描述:Temperature Sensor IC |
| LM70CIMMX-3 | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM70CIMMX-3/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。