5V AC Electrical Characteristics
(Note 13)
Unless otherwise specified, all limits guaranteed for at T
J
= 25C, V
CM
=
1
2
V
S
and R
L
= 2k
.
Boldface
limits apply at the tem-
perature extremes.
Symbol
Parameter
Conditions
Min
(Note 6)
Typ
(Note 5)
11
15.3
24
56
270
21
53
Max
(Note 6)
Units
SR
Slew Rate (Note 9)
Unity Gain Bandwidth Product
3dB Frequency
Phase Margin
Settling Time (0.1%)
Propagation Delay
2
nd
Harmonic Distortion
F
IN
= 1MHz (Note 10)
3rd Harmonic Distortion
F
IN
= 1MHz (Note 10)
Input-Referred Voltage Noise
A
V
= +1, V
IN
= 3.5V
PP
V/μs
MHz
MHz
deg
ns
ns
dBc
A
V
= +1
10
Φ
m
t
s
t
p
HD2
A
V
= 1, V
O
=
±
1V, R
L
= 500
A
V
= 2, V
IN
=
±
1V, R
L
= 500
V
OUT
= 2V
PP
HD3
V
OUT
= 2V
PP
40
dBc
e
n
f = 10kHz
23
nV/
Note 1:
Note 1: Absolute maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the
device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical
Characteristics.
Note 2:
For testing purposes, ESD was applied using human body model, 1.5k
in series with 100pF.
Note 3:
Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the
maximum allowed junction temperature of 150C
Note 4:
The maximum power dissipation is a function of T
J(MAX)
,
θ
JA
, and T
A
. The maximum allowable power dissipation at any ambient temperature is
P
D
= (T
J(MAX)
- T
A
)/
θ
JA
. All numbers apply for packages soldered directly onto a PC board.
Note 5:
Typical values represent the most likely parametric norm.
Note 6:
All limits are guaranteed by testing or statistical analysis.
Note 7:
Large signal voltage gain is the total output swing divided by the input signal required to produce that swing.
Note 8:
The open loop output current is guaranteed, by the measurement of the open loop output voltage swing.
Note 9:
Slew rate is the average of the raising and falling slew rates.
Note 10:
Harmonics are measured with A
V
= +2 and R
L
= 100
and V
IN
= 1V
PP
to give V
OUT
= 2V
PP
.
Note 11:
Continuous operation at these output currents will exceed the power dissipation ability of the device
Note 12:
Power dissipation limits may be exceeded if all four amplifiers source or sink 40mA. Voltage across the output transistors and their output currents must
be taken into account to determine the power dissipation of the device
Note 13:
Electrical table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of
the device such that T
= T
. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self heating where T
J
>
T
A
.
See applications section for information on temperature de-rating of this device.
Connection Diagram
14-Pin SOIC/TSSOP
20073402
Top View
Ordering Information
Package
Part Number
LM6588MA
LM6588MAX
LM6588MT
LM6588MTX
Package Marking
Transport Media
95 Units/Rail
2.5k Units Tape and Reel
95 Units/Rail
2.5k Units Tape and Reel
NSC Drawing
14-Pin SOIC
LM6588MA
M14A
14-Pin TSSOP
LM6588MT
MTC14
L
www.national.com
4