- 您現在的位置：買賣IC網 > PDF目錄385488 > LM62BIM3 (National Semiconductor Corporation) 2.7V, 15.6 mV/∑C SOT-23 Temperature Sensor PDF資料下載
參數資料
| 型號： | LM62BIM3 |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | 2.7V, 15.6 mV/∑C SOT-23 Temperature Sensor |
| 中文描述： | 2.7，15.6毫伏/ΣCSOT - 23封裝溫度傳感器 |
| 文件頁數： | 4/7頁 |
| 文件大?。?/td> | 218K |
| 代理商： | LM62BIM3 |
Typical Performance Characteristics
printed circuit board as shown in Figure 2 (Continued)
To generate these curves the LM62 was mounted to a
1.0 Mounting
The LM62 can be applied easily in the same way as other
integrated-circuit temperature sensors. It can be glued or ce-
mented to a surface. The temperature that the LM62 is sens-
ing will be within about +0.2C of the surface temperature
that LM62’s leads are attached to.
This presumes that the ambient air temperature is almost the
same as the surface temperature; if the air temperature were
much higher or lower than the surface temperature, the ac-
tual temperature measured would be at an intermediate tem-
perature between the surface temperature and the air tem-
perature.
To ensure good thermal conductivity the backside of the
LM62 die is directly attached to the GND pin. The lands and
traces to the LM62 will, of course, be part of the printed cir-
cuit board, which is the object whose temperature is being
measured. These printed circuit board lands and traces will
not cause the LM62’s temperature to deviate from the de-
sired temperature.
Alternatively, the LM62 can be mounted inside a sealed-end
metal tube, and can then be dipped into a bath or screwed
into a threaded hole in a tank. As with any IC, the LM62 and
accompanying wiring and circuits must be kept insulated and
dry, to avoid leakage and corrosion. This is especially true if
the circuit may operate at cold temperatures where conden-
sation can occur. Printed-circuit coatings and varnishes such
as Humiseal and epoxy paints or dips are often used to en-
sure that moisture cannot corrode the LM62 or its connec-
tions.
The thermal resistance junction to ambient (
θ
) is the pa-
rameter used to calculate the rise of a device junction tem-
perature due to its power dissipation. For the LM62 the
equation used to calculate the rise in the die temperature is
as follows:
T
J
= T
A
+
θ
JA
[(+V
S
I
Q
) + (+V
S
V
O
) I
L
]
where I
is the quiescent current and I
is the load current on
the output. Since the LM62’s junction temperature is the ac-
tual temperature being measured care should be taken to
minimize the load current that the LM62 is required to drive.
Supply Voltage
vs Supply Current
DS100893-12
Start-Up Response
DS100893-22
DS100893-14
FIGURE 2. Printed Circuit Board Used
for Heat Sink to Generate All Curves.
1
2
" Square Printed Circuit Board
with 2 oz. Copper Foil or Similar.
www.national.com
4
相關PDF資料 |
PDF描述 |
|---|---|
| LM62BIM3X | 2.7V, 15.6 mV/∑C SOT-23 Temperature Sensor |
| LM62CIM3 | 2.7V, 15.6 mV/∑C SOT-23 Temperature Sensor |
| LM6310 | High Speed Low Power Operational Amplifier with TRI-STATE Output |
| LM6310IM | High Speed Low Power Operational Amplifier with TRI-STATE Output |
| LM6310IMX | High Speed Low Power Operational Amplifier with TRI-STATE Output |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM62BIM3/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM62BIM3X | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM62BIM3X/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM62CIM3 | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM62CIM3/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。