- 您現在的位置：買賣IC網 > PDF目錄358871 > LM629N-6 (NATIONAL SEMICONDUCTOR CORP) Precision Motion Controller PDF資料下載
參數資料
| 型號： | LM629N-6 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | Precision Motion Controller |
| 中文描述： | BRUSH DC MOTOR CONTROLLER, PDIP28 |
| 封裝： | PLASTIC, DIP-28 |
| 文件頁數： | 11/24頁 |
| 文件大小： | 630K |
| 代理商： | LM629N-6 |
Theory of Operation
(Continued)
LM628 READING AND WRITING OPERATIONS
The host processor writes commands to the LM628 via the
host I/O port when Port Select (PS ) input (Pin 16) is logic
low. The desired command code is applied to the parallel
port line and the Write (WR ) input (Pin 15) is strobed. The
command byte is latched into the LM628 on the rising edge
of the WR input. When writing command bytes it is neces-
sary to first read the status byte and check the state of a flag
called the “busy bit” (Bit 0). If the busy bit is logic high, no
command write may take place. The busy bit is never high
longer than 100 μs, and typically falls within 15 μs to 25 μs.
The host processor reads the LM628 status byte in a similar
manner: by strobing the Read (RD ) input (Pin 13) when PS
(Pin 16) is low; status information remains valid as long as
RD is low.
Writing and reading data to/from the LM628 (as opposed to
writing commands and reading status) are done with PS (Pin
16) logic high. These writes and reads are always an integral
number (from one to seven) of two-byte words, with the first
byte of each word being the more significant. Each byte re-
quires a write (WR ) or read (RD ) strobe. When transferring
data words (byte-pairs), it is necessary to first read the status
byte and check the state of the busy bit. When the busy bit is
logic low, the user may then sequentially transfer both bytes
comprising a data word, but the busy bit must again be
checked and found to be low before attempting to transfer
the next byte pair (when transferring multiple words). Data
transfers are accomplished via LM628-internal interrupts
(which are not nested); the busy bit informs the host proces-
sor when the LM628 may not be interrupted for data transfer
(or a command byte). If a command is written when the busy
bit is high, the command will be ignored.
The busy bit goes high immediately after writing a command
byte, or reading or writing a second byte of data (See Figure
5 thru Figure 7).
MOTOR OUTPUTS
The LM628 DAC output port can be configured to provide ei-
ther a latched eight-bit parallel output or a multiplexed 12-bit
output. The 8-bit output can be directly connected to a
flow-through (non-input-latching) D/A converter; the 12-bit
output can be easily demultiplexed using an external 6-bit
latch and an input-latching 12-bit D/A converter. The DAC
output data is offset-binary coded; the 8-bit code for zero is
80 hex and the 12-bit code for zero is 800 hex. Values less
than these cause a negative torque to be applied to the mo-
tor and, conversely, larger values cause positive motor
torque. The LM628, when configured for 12-bit output, pro-
vides signals which control the demultiplexing process. See
for details.
The LM629 provides 8-bit, sign and magnitude PWM output
signals for directly driving switch-mode motor-drive amplifi-
ers. Figure 11 shows the format of the PWM magnitude out-
put signal.
TABLE 2. LM628 User Command Set
Command
Type
Description
Hex
Data
Bytes
0
0
0
0
0
2
2
4
4
Note
RESET
PORT8
PORT12
DFH
SIP
LPEI
LPES
SBPA
SBPR
Initialize
Initialize
Initialize
Initialize
Interrupt
Interrupt
Interrupt
Interrupt
Interrupt
Reset LM628
Select 8-Bit Output
Select 12-Bit Output
Define Home
Set Index Position
Interrupt on Error
Stop on Error
Set Breakpoint, Absolute
Set Breakpoint, Relative
00
05
06
02
03
1B
1A
20
21
1
2
2
1
1
1
1
1
1
DS009219-13
FIGURE 11. PWM Output Signal Format (Sign output (pin 18) not shown)
L
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| LM629N-8 | Precision Motion Controller |
| LM629 | Precision Motion Controller |
| LM63CIMA | 【1C/【3C Accurate Remote Diode Digital Temperature Sensor with Integrated Fan Control |
| LM63CIMAX | 【1C/【3C Accurate Remote Diode Digital Temperature Sensor with Integrated Fan Control |
| LM6402G | N CHANNEL E/D MOS LSI 4 BIT MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM629N6 | 制造商:Texas Instruments 功能描述:IC MOTION CONTROLLER DIP28 629 |
| LM629N-6/NOPB | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LM629N-8 | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LM629N-8/NOPB | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LM62BIM3 | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。