- 您現在的位置：買賣IC網 > PDF目錄358871 > LM629M-8 (NATIONAL SEMICONDUCTOR CORP) Precision Motion Controller PDF資料下載
參數資料
| 型號： | LM629M-8 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | Precision Motion Controller |
| 中文描述： | BRUSH DC MOTOR CONTROLLER, PDSO24 |
| 封裝： | SOP-24 |
| 文件頁數： | 12/24頁 |
| 文件大小： | 630K |
| 代理商： | LM629M-8 |
Theory of Operation
(Continued)
TABLE 2. LM628 User Command Set
(Continued)
Command
Type
Description
Hex
Data
Bytes
2
2
2 to 10
0
2 to 14
0
1
2
4
4
4
4
2
2
Note
MSKI
RSTI
LFIL
UDF
LTRJ
STT
RDSTAT
RDSIGS
RDIP
RDDP
RDRP
RDDV
RDRV
RDSUM
Interrupt
Interrupt
Filter
Filter
Trajectory
Trajectory
Report
Report
Report
Report
Report
Report
Report
Report
Mask Interrupts
Reset Interrupts
Load Filter Parameters
Update Filter
Load Trajectory
Start Motion
Read Status Byte
Read Signals Register
Read Index Position
Read Desired Position
Read Real Position
Read Desired Velocity
Read Real Velocity
Read Integration Sum
1C
1D
1E
04
1F
01
None
0C
09
08
0A
07
0B
0D
1
1
1
1
1
3
1, 4
1
1
1
1
1
1
1
Note 4:
Commands may be executed “On the Fly” during motion.
Note 5:
Commands not applicable to execution during motion.
Note 6:
Command may be executed during motion if acceleration parameter was not changed.
Note 7:
Command needs no code because the command port status-byte read is totally supported by hardware.
User Command Set
GENERAL
The following paragraphs describe the user command set of
the LM628. Some of the commands can be issued alone and
some require a supporting data structure. As examples, the
command STT (STarT motion) does not require additional
data; command LFIL (Load FILter parameters) requires ad-
ditional data (derivative-term sampling interval and/or filter
parameters).
Commands are categorized by function: initialization, inter-
rupt control, filter control, trajectory control, and data report-
ing. The commands are listed in Table 2and described in the
following paragraphs. Along with each command name is its
command-byte code, the number of accompanying data
bytes that are to be written (or read), and a comment as to
whether the command is executable during motion.
Initialization Commands
The following four LM628 user commands are used primarily
to initialize the system for use.
RESET COMMAND: RESET the LM628
Command Code:
Data Bytes:
Executable During Motion: Yes
This command (and the hardware reset input, Pin 27) results
in setting the following data items to zero: filter coefficients
and their input buffers, trajectory parameters and their input
buffers, and the motor control output. A zero motor control
output is a half-scale, offset-binary code: (80 hex for the 8-bit
output mode; 800 hex for 12-bit mode). During reset, the
DAC port outputs 800 hex to “zero” a 12-bit DAC and reverts
to 80 hex to “zero” an 8-bit DAC. The command also clears
five of the six interrupt masks (only the SBPA/SBPR interrupt
00 Hex
None
is masked), sets the output port size to 8 bits, and defines
the current absolute position as home. Reset, which may be
executed at any time, will be completed in less than 1.5 ms.
Also see commands PORT8 and PORT12.
PORT8 COMMAND: Set Output PORT Size to 8 Bits
Command Code:
Data Bytes:
Executable During Motion: Not Applicable
The default output port size of the LM628 is 8 bits; so the
PORT8 command need not be executed when using an 8-bit
DAC. This command must not be executed when using a
12-bit converter; it will result in erratic, unpredictable motor
behavior. The 8-bit output port size is the required selection
when using the LM629, the PWM-output version of the
LM628.
05 Hex
None
PORT12 COMMAND: Set Output PORT Size to 12 Bits
Command Code:
Data Bytes:
Executable During Motion: Not Applicable
When a 12-bit DAC is used, command PORT12 should be
issued very early in the initialization process. Because use of
this command is determined by system hardware, there is
only one foreseen reason to execute it later: if the RESET
command is issued (because an 8-bit output would then be
selected as the default) command PORT12 should be imme-
diately executed. This command must not be issued when
using an 8-bit converter or the LM629, the PWM-output ver-
sion of the LM628.
06 Hex
None
DFH COMMAND: DeFine Home
Command Code:
Data Bytes:
Executable During Motion: Yes
02 Hex
None
L
www.national.com
12
相關PDF資料 |
PDF描述 |
|---|---|
| LM629N-6 | Precision Motion Controller |
| LM629N-8 | Precision Motion Controller |
| LM629 | Precision Motion Controller |
| LM63CIMA | 【1C/【3C Accurate Remote Diode Digital Temperature Sensor with Integrated Fan Control |
| LM63CIMAX | 【1C/【3C Accurate Remote Diode Digital Temperature Sensor with Integrated Fan Control |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM629M-8 | 制造商:Texas Instruments 功能描述:MOTION CONTROL SMD SOIC24 629 |
| LM629M-8/NOPB | 功能描述:馬達/運動/點火控制器和驅動器 PRECISION MOTION CONTROLLER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LM629MX-8 | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LM629MX-8/NOPB | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LM629N6 | 制造商:Texas Instruments 功能描述:IC, MOTION CONTROLLER, DIP28, 629 制造商:Texas Instruments 功能描述:IC, MOTION CONTROLLER, DIP28, 629; Motor Type:DC Brushless Servo; No. of Outputs:8; Output Current:1.6mA; Output Voltage:2.4V; Driver Case Style:DIP; No. of Pins:28; Supply Voltage Min:4.5V; Supply Voltage Max:5.5V; Operating ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。