- 您現在的位置：買賣IC網 > PDF目錄358871 > LM6172IMX (NATIONAL SEMICONDUCTOR CORP) Dual High Speed, Low Power, Low Distortion, Voltage Feedback Amplifiers PDF資料下載
參數資料
| 型號： | LM6172IMX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | Dual High Speed, Low Power, Low Distortion, Voltage Feedback Amplifiers |
| 中文描述： | 2 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| 封裝： | 0.150 INCH, PLASTIC, SOIC-8 |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 551K |
| 代理商： | LM6172IMX |
Power Supply Bypassing
(Continued)
Termination
In high frequency applications, reflections occur if signals
are not properly terminated. Figure 6shows a properly termi-
nated signal while Figure 7 shows an improperly terminated
signal.
To minimize reflection, coaxial cable with matching charac-
teristic impedance to the signal source should be used. The
other end of the cable should be terminated with the same
value terminator or resistor. For the commonly used cables,
RG59 has 75
characteristic impedance, and RG58 has
50
characteristic impedance.
Power Dissipation
The maximum power allowed to dissipate in a device is de-
fined as:
P
D
= (T
J(max)
T
A
)/
θ
JA
Where P
D
is the power dissipation in a device
T
J(max)
is the maximum junction temperature
T
A
is the ambient temperature
θ
JA
is the thermal resistance of a particular package
For example, for the LM6172 in a SO-8 package, the maxi-
mum power dissipation at 25C ambient temperature is
780 mW.
Thermal resistance,
θ
, depends on parameters such as
die size, package size and package material. The smaller
the die size and package, the higher
θ
becomes. The 8-pin
DIP package has a lower thermal resistance (95C/W) than
that of 8-pin SO (160C/W). Therefore, for higher dissipation
capability, use an 8-pin DIP package.
The total power dissipated in a device can be calculated as:
P
D
= P
Q
+ P
L
P
is the quiescent power dissipated in a device with no load
connected at the output. P
is the power dissipated in the de-
vice with a load connected at the output; it is not the power
dissipated by the load.
Furthermore,
P
Q
:
=
supply current x total supply voltage with no load
P
L
:
=
output current x (voltage difference between sup-
ply voltage and output voltage of the same supply)
For example, the total power dissipated by the LM6172 with
V
=
±
15V and both channels swinging output voltage of
10V into 1 k
is
P
D
:
=
P
Q
+ P
L
:
=
2[(2.3 mA)(30V)] + 2[(10 mA)(15V 10V)]
:
=
138 mW + 100 mW
:
=
238 mW
DS012581-47
FIGURE 5. Power Supply Bypassing
DS012581-53
FIGURE 6. Properly Terminated Signal
DS012581-54
FIGURE 7. Improperly Terminated Signal
www.national.com
13
相關PDF資料 |
PDF描述 |
|---|---|
| LM6172IM | Dual High Speed, Low Power, Low Distortion, Voltage Feedback Amplifiers |
| LM6172 | Dual High Speed, Low Power, Low Distortion, Voltage Feedback Amplifiers |
| LM621 | LM621 Brushless Motor Commutator |
| LM6218AWMX | Voltage-Feedback Operational Amplifier |
| LM6218AWM | Voltage-Feedback Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM6172IMX/NOPB | 功能描述:運算放大器 - 運放 DUAL HI-SPD LO-PWR LO-DIST VOL FDBK AMP RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| LM6172IN | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| LM6172IN/NOPB | 功能描述:運算放大器 - 運放 Dual High Speed,Low Pwr Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| LM6172IN/NOPB | 制造商:Texas Instruments 功能描述:Operational Amplifier (Op-Amp) IC |
| LM6172MDR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Dual High Speed, Low Power, Low Distortion, Voltage Feedback Amplifiers |
發布緊急采購，3分鐘左右您將得到回復。