參數資料
型號: LM56
廠商: National Semiconductor Corporation
英文描述: Aluminum Electrolytic Capacitor; Capacitor Type:High Temperature; Voltage Rating:40VDC; Capacitor Dielectric Material:Aluminum Electrolytic; Operating Temperature Range:-55 C to +125 C; Capacitance:680uF RoHS Compliant: Yes
中文描述: 雙路輸出低功耗溫控器
文件頁數: 8/13頁
文件大?。?/td> 370K
代理商: LM56
Application Hints
2.0
For simplicity the following is an analysis of the trip point ac-
curacy using the single output configuration show in Figure 2
with a set point of 82C.
Trip Point Error Voltage = V
TPE
,
Comparator Offset Error for V
T1E
Temperature Sensor Error = V
TSE
Reference Output Error = V
RE
LM56 TRIP POINT ACCURACY SPECIFICATION
1. V
TPE
=
±
V
T1E
V
TSE
+ V
RE
Where:
2. V
T1E
=
±
8 mV (max)
3. V
TSE
= (6.20 mV/C) x (
±
3C) =
±
18.6 mV
4. V
RE
= 1.250V x (
±
0.01) R2/(R1 + R2)
Using Equations from page 1 of the datasheet.
V
T1
=1.25VxR2/(R1+R2)=(6.20 mV/C)(82C) +395 mV
Solving for R2/(R1 + R2) = 0.7227
then,
5. V
RE
= 1.250V x (
±
0.01) R2/(R1 + R2) = (0.0125) x
(0.7227) =
±
9.03 mV
The individual errors do not add algebraically because, the
odds of all the errors being at their extremes are rare. This is
proven by the fact the specification for the trip point accuracy
stated in the Electrical Characteristic for the temperature
range of 40C to +125C, for example, is specified at
±
3C
for the LM56BIM. Note this trip point error specification does
not include any error introduced by the tolerance of the ac-
tual resistors used, nor any error introduced by power supply
variation.
If the resistors have a
±
0.5% tolerance, an additional error of
±
0.4C will be introduced. This error will increase to
±
0.8C
when both external resistors have a
±
1% tolerance.
3.0
TRIP POINT ACCURACY
Bias current for the comparator inputs is 300 nA (max) each,
over the specified temperature range and will not introduce
considerable error if the sum of the resistor values are kept
to about 27 k
as shown in the typical application of Figure
1 . This bias current of one comparator input will not flow if
the temperature is well below the trip point level. As the tem-
perature approaches trip point level the bias current will start
to flow into the resistor network. When the temperature sen-
sor output is equal to the trip point level the bias current will
be 150 nA(max). Once the temperature is well above the trip
point level the bias current will be 300 nA (max). Therefore,
the first trip point will be affected by 150 nA of bias current.
The leakage current is very small when the comparator input
transistor of the different pair is off (see Figure 3) .
The effect of the bias current on the first trip point can be de-
fined by the following equations:
BIAS CURRENT EFFECT ON
where I
B
= 300 nA (the maximum specified error).
The effect of the bias current on the second trip point can be
defined by the following equations:
where I
B
= 300 nA (the maximum specified error).
The closer the two trip points are to each other the more sig-
nificant the error is. Worst case would be when V
T1
= V
T2
=
V
REF
/2.
DS012893-17
FIGURE 2. Single Output Configuration
L
www.national.com
8
相關PDF資料
PDF描述
LM56BIM Dual Output Low Power Thermostat
LM56BIMM Dual Output Low Power Thermostat
LM56BIMMX Dual Output Low Power Thermostat
LM56BIMX Dual Output Low Power Thermostat
LM56CIM Dual Output Low Power Thermostat
相關代理商/技術參數
參數描述
LM56_06 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Dual Output Low Power Thermostat
LM560 功能描述:標準LED-通孔 Warm White RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube
LM560A 功能描述:標準LED-通孔 Warm White RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube
LM560A 制造商:Seoul Semiconductor 功能描述:LED 5MM WARM WHITE
LM560A_1 制造商:SEOUL 制造商全稱:Seoul Semiconductor 功能描述:WARM WHITE LAMP LED