- 您現在的位置：買賣IC網 > PDF目錄358868 > LM5025A (National Semiconductor Corporation) Active Clamp Voltage Mode PWM Controller PDF資料下載
參數資料
| 型號： | LM5025A |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Active Clamp Voltage Mode PWM Controller |
| 中文描述： | 有源鉗位電壓模式PWM控制器 |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 698K |
| 代理商： | LM5025A |
Current Limit
(Continued)
the PWM comparator will produce the first output pulse at
OUT_A. After the first pulse occurs, the softstart current
source will revert to the normal 20μA level. Fully discharging
and then slowly charging the SS capacitor protects a con-
tinuously over-loaded converter with a low duty cycle hiccup
mode.
These two modes of over-current protection allow the user
great flexibility to configure the system behavior in over-load
conditions. If it is desired for the system to act as a current
source during an over-load, then the CS1 cycle-by-cycle
current limiting should be used. In this case the current
sense signal should be applied to the CS1 input and the CS2
input should be grounded. If during an overload condition it is
desired for the system to briefly shutdown, followed by soft-
start retry, then the CS2 hiccup current limiting mode should
be used. In this case the current sense signal should be
applied to the CS2 input and the CS1 input should be
grounded. This shutdown / soft-start retry will repeat indefi-
nitely while the over-load condition remains. The hiccup
mode will greatly reduce the thermal stresses to the system
during heavy overloads. The cycle-by-cycle mode will have
higher system thermal dissipations during heavy overloads,
but provides the advantage of continuous operation for short
duration overload conditions.
It is possible to utilize both over-current modes concurrently,
whereby slight overload conditions activate the CS1 cycle-
by-cycle mode while more severe overloading activates the
CS2 hiccup mode. Generally the CS1 input will always be
configured to monitor the main switch FET current each
cycle. The CS2 input can be configured in several different
ways depending upon the system requirements.
a) The CS2 input can also be set to monitor the main switch
FET current except scaled to a higher threshold than CS1
b) An external over-current timer can be configured which
trips after a pre-determined over-current time, driving the
CS2 input high, initiating a hiccup event.
c) In a closed loop voltage regulaton system, the COMP
input will rise to saturation when the cycle-by-cycle current
limit is active. An external filter/delay timer and voltage di-
vider can be configured between the COMP pin and the CS2
pin to scale and delay the COMP voltage. If the CS2 pin
voltage reaches 0.5V a hiccup event will initiate.
A small RC filter, located near the controller, is recom-
mended for each of the CS pins. The CS1 input has an
internal FET which discharges the current sense filter ca-
pacitor at the conclusion of every cycle, to improve dynamic
performance. This same FET remains on an additional 50ns
at the start of each main switch cycle to attenuate the leading
edge spike in the current sense signal. The CS2 discharge
FET only operates following a CS2 event, UVLO and thermal
shutdown.
The LM5025A CS comparators are very fast and may re-
spond to short duration noise pulses. Layout considerations
are critical for the current sense filter and sense resistor. The
capacitor associated with the CS filter must be placed very
close to the device and connected directly to the pins of the
IC (CS and GND). If a current sense transformer is used,
both leads of the transformer secondary should be routed to
the filter network , which should be located close to the IC. If
a sense resistor in the source of the main switch MOSFET is
used for current sensing, a low inductance type of resistor is
required. When designing with a current sense resistor, all of
the noise sensitive low power ground connections should be
connected together near the IC GND and a single connec-
tion should be made to the power ground (sense resistor
ground point).
20107414
Oscillator and Sync Capability
The LM5025A oscillator is set by a single external resistor
connected between the RT pin and GND. To set a desired
oscillator frequency (F), the necessary RT resistor can be
calculated from:
RT = (5725/F)
1.026
where F is in kHz and RT in k
.
The RT resistor should be located very close to the device
and connected directly to the pins of the IC (RT and GND).
A unique feature of LM5025A is the ability to synchronize the
oscillator to an external clock with a frequency that is either
higher or lower than the frequency of the internal oscillator.
The lower frequency sync frequency range is 80% of the free
running internal oscillator frequency. There is no constraint
on the maximum SYNC frequency.Aminimum pulse width of
100ns is required for the synchronization clock . If the syn-
chronization feature is not required, the SYNC pin should be
connected to GND to prevent any abnormal interference .
The internal oscillator can be completely disabled by con-
necting the RT pin to REF. Once disabled, the sync signal
will act directly as the master clock for the controller. Both the
frequency and the maximum duty cycle of the PWM control-
ler can be controlled by the SYNC signal (within the limita-
tions of the Volt x Second Clamp). The maximum duty cycle
(D) will be (1-D) of the SYNC signal.
Feed-Forward Ramp
An external resistor (R
FF
) and capacitor (C
FF
) connected to
V
IN
and GND are required to create the PWM ramp signal.
The slope of the signal at the RAMP pin will vary in propor-
tion to the input line voltage. This varying slope provides line
feedforward information necessary to improve line transient
response with voltage mode control. The RAMP signal is
L
www.national.com
12
相關PDF資料 |
PDF描述 |
|---|---|
| LM5025AMTC | Active Clamp Voltage Mode PWM Controller |
| LM5025AMTCX | Active Clamp Voltage Mode PWM Controller |
| LM5025ASD | Active Clamp Voltage Mode PWM Controller |
| LM5025ASDX | Active Clamp Voltage Mode PWM Controller |
| LM5033 | 100V Push-Pull Voltage Mode PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM5025AEVAL | 功能描述:BOARD EVALUATION LM5025A RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:PowerWise® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| LM5025AEVAL/NOPB | 功能描述:電源管理IC開發工具 LM5025A EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LM5025AMTC | 功能描述:電壓模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| LM5025AMTC/NOPB | 功能描述:電壓模式 PWM 控制器 100V Forward Active Clamp RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| LM5025AMTCX | 制造商:Texas Instruments 功能描述:Voltage Mode PWM Controller 3A/1A 16-Pin TSSOP T/R |
發布緊急采購，3分鐘左右您將得到回復。